WTB: 350 parts.

[Blackwizard222]

Looking for parts for a 350 small block:
Performance hydraulic flat cam
Performance Intake manifold
Performance heads
Holley carb
Long tubes for an el camino (1979)
Rear end out of a monte carlo or el camino with 3.73 gears
Stall vert for th350.

List what ya got and how much u want!

[9secfirebird]

i have an intake manifold. weiand Xcellerator. it looks great and is a real powerful unit. 55.00 would be good, its got very very low miles on it and looks awesome lemme know if your interested! i have ATON of small block **** sittin around my houselemme know what else you might need.

[NJSPEEDER]

a clearer definition of "performance" would be good.
i have a few blocks that would be good for rebuild, iron eagle heads that will work in you wanna spin it to 6500rpm or so, a few intake ranging from a performer rpm to a tunnel ram.
i also have a 400sbc 4bolt block, a spare 350 crank and rod set, and other misc. stuff around.

later
tim

[Blackwizard222]

Well, strip/street stuff, its goin on a 1979 el camino thats registered QQ.

The short block is done, i just am looking for top end parts:
Heads
Single plane intakes
Holley carbs
Cams
Gear drive
Headers
Flowmaster mufflers
ETC...

The car has a performer on it now so if u got any single planes let me know.

[9secfirebird]

my weiand is a single plain!!!!!

[Blackwizard222]

ok well im peicing together what i want and such. if i decide i want it ill be sure to email you. :)

[9secfirebird]

i have a nice 7 second motor for ya ;) only 4,000 and its yours its a short block but its a steal at that price.

[bad64chevelle]

Hey 9 second...happen to have an oil bypass valve for a 327?

[NJSPEEDER]

9secbirds weiand intake and my iron eagle heads would make the basis of a nice combo :) grab a cam so that you can shift at 6500-7000rpm and you would be flying.

later
tim

[Blackwizard222]

what do u want for the heads? what r the specs on them? im not planning on going much bigger than comp cams 270h magnum. gear 3.73 and mininal stall.

[Slow Z]

Hey my friend has an 8.5" GN rear with driveshaft he'd probably sell ya.. All fresh parts.

[Slow Z]

i have a nice 7 second motor for ya ;) only 4,000 and its yours its a short block but its a steal at that price.

7 second? in what the 1/8th?

[9secfirebird]

do everyone a favor and only ask a question about the item or respond to the item if you are seriously considering it. if your not, dont waste everyones time and bandwith.

[Blackwizard222]

*EDIT*

[Tru2Chevy]

just because i havent responded to you in a split second with a decision doesnt mean im not considering it. Â*But **** with that kinda attitude i doubt ull sell anything.

Learn to have patience.

I think 9sec's comment was directed at Slow Z, not you.

- Justin

[9secfirebird]

yes it was. thanks justin.

[Slow Z]

That was a serious question... Lets see a motor that goes 7.999 in a 3000lb car would be making around 1200HP... Now a SBC shortblock that'll handle over 1200HP would look something like this:

Dart Little M block w/ billet caps: $2100
Callies 4340 Dragon Slayer Crank: $800
Oliver Billet rods: $1300
JE Pro Series pistons: $800
All other goodies + machine work: $1000
Total: Atleast $6000, probably consideribly more.

So if you have a shortblock like that and you want $4000 I might have you a buyer.

[Blackwizard222]

yes it was. thanks justin.
Oh my bad.

[Tru2Chevy]

Please take further discussion of the $4,000 shortblock in question here:

http://www.njfboa.org/forums/viewtopic.php?t=3515

Thanks guys.

- Justin

[9secfirebird]

slowZ - click on the link in the above thread, my response is there

[Blackwizard222]

ok

we got a stall converter, cam, and headers already.

I want your manifold 9sec.

So that leaves me needing a set of heads with 64cc chambers and at least 1.94/1.50 valves. Not looking for aftermarket heads (too much $$$).

Also need a set of dumped flowmasters

Rear end with 3.73 posi for a G body

[Mike]

lol didnt herman tell you to ask me about elcamino parts?.........ill ask my dad tomorow to see what he has laying around.

[Blackwizard222]

Hey my friend has an 8.5" GN rear with driveshaft he'd probably sell ya.. All fresh parts.

what kinda gears? posi? how much?

im looking for a g body rear with 3.73 posi. monte carlo ss, gn, etc...

[Blackwizard222]

lol didnt herman tell you to ask me about elcamino parts?.........ill ask my dad tomorow to see what he has laying around.
no herman didnt lol. forgot u had one. let me know what u got. my dad wants a hood too, if ya still got one.

[Blackwizard222]

got heads and manifold. i need a rear and thats really about it.

[Slow Z]

I believe its 3.42, definately posi it was just re-done. I'll give him a call about it... I'd assume he'd want atleast $700 for it but who knows, maybe cheaper. Either way a sub-$900 GN rear with driveshaft is a steal.

[Blackwizard222]

no thanks, ill get a stock 3.73 posi from a monte carlo for it.