Build Me A Motor....

[Zero4488]

Can any one out there build me a 383 for my car?

[jrsfast84]

What kind of motor do you want street, or strip or both, racing gas pump gas,carb'ed or F.I., i have plenty of parts and one motor for sale. JR1.

[Zero4488]

I want a TPI 350 block with a 383 stroker kit....I want it as a street and strip kinda deal....I want it nitrous safe and maybe a turbo down the road.....

[WayFast84]

What kind of motor do you want street, or strip or both, racing gas pump gas,carb'ed or F.I., i have plenty of parts and one motor for sale. JR1.
Hey, How much would it cost for a 11 sec all motor 350 that can handle a 100 shot?

[78camaro]

Hey, How much would it cost for a 11 sec all motor 350 that can handle a 100 shot?


if you want 11's all n/a why not going bigger cubes liek a 400 or even a 383

[Ian]

zero4488, I doubt you want to use a TPI block for your build up. I'm pretty sure most of them were 2 bolt blocks, not exactly nitrous safe or ready for a turbo.

wayfast, if you want 11's all motor, either build a bigger motor than a 350 or get an LS1.

[WayFast84]

zero4488, I doubt you want to use a TPI block for your build up. I'm pretty sure most of them were 2 bolt blocks, not exactly nitrous safe or ready for a turbo.

wayfast, if you want 11's all motor, either build a bigger motor than a 350 or get an LS1.
Ok so how much for a 11 sec all motor 355? that can handle a 100 shot!

[Tru2Chevy]

Umm...11's with a 350 shouldn't be hard at all if the car was prepped right.

But 400 block FTW!

- Justin

[Ian]

Ok so how much for a 11 sec all motor 355? that can handle a 100 shot!

:roll:

an extra 5 cubes isnt gonna do much. A larger motor will make more power than a smaller motor. If you want to go fast, build up a 406 small block. any bigger than that and you're gonna have to buy an aftermarket block/crank.

[Ian]

Umm...11's with a 350 shouldn't be hard at all if the car was prepped right.

But 400 block FTW!

- Justin

I know its not hard to acomplish with a 350, but its easier on the motor if it's bigger. It'll be more streetable and less finicky with the extra cubes.

[Rob WS6]

zero4488, I doubt you want to use a TPI block for your build up. I'm pretty sure most of them were 2 bolt blocks, not exactly nitrous safe or ready for a turbo.



Theres absolutley nothing wrong with l98 blocks... thats why they make splayed caps! :D

[Jared1970Chevelle]

what kind of car is it going in? what the car weigh? what trans? what rear? what suspension? 11's streetable is not that bad if you got the $$... its not cheap.... i can build you a motor for 300 over the cost of the GOFAST parts you want in it.,...

let me know
Jared

[HardcoreZ28]

I can also put together a nice engine for you. I'd suggest using a 1 piece rear main seal truck block with 4 bolt mains. That's the route I went with my car. I'm running a 383 with a Super Ram setup in my IROC. If you're interested shoot me a PM of check out my company website in the sig and get in touch with me through there.

[EVIL90SS]

small blocks are for the weak

[DieselKickYoAss4Sure]

=WayFast84]Ok so how much for a 11 sec all motor 355? that can handle a 100 shot!
dude forget the NAWZ, 11sec NA is perfecly easy to do with a small block, thats my opinion. Personally i would go with an engine with some real potential like a diesel :0 J/K