PDA

View Full Version : how much will my steel driveshaft slow me down?


98tadriver
06-23-2006, 08:31 PM
how much will my steel driveshaft slow me down?

Im gonna go to atco on tuesday night with my drag radials, and was just curious. its noticeably heavier than my stock aluminum shaft was..

i should still be able to run faster right?

qwikz28
06-23-2006, 10:22 PM
i heard on ls1tech that no one has seen any gains/losses from swapping driveshafts. so i think you'll be good dood :)

Koll
06-23-2006, 10:32 PM
Its just less rotating mass = rev faster. In effect it anything to reduce either the weight or rotating mass will help.

JSPERFORMANCE
06-24-2006, 08:17 AM
I have had both and I noticed 0 diffrence in acceleration, 1/4 mile et or 60'times. But the aluminum driveshaft sure does look nicer though.

deadtrend1
06-24-2006, 10:02 AM
..... But the aluminum driveshaft sure does look nicer though.

mhmm, just made it difficult to find the pinion angle since the magnetic angle finder doesnt stick to it easily....:laugh:

BMF
06-24-2006, 11:54 AM
One of my fellow racers has done the test, and the aluminum shaft is quicker.

In a 68' Chevelle, the stock steel shaft was compaired to a Denny's Aluminum driveshaft and the aluminum shaft was 4 hundreths quicker (0.04).

This test was done on a car that sees typically 180-250 passes in a season of racing, and the results are accurate.



If you can see it on the slip or not, if you add rotating mass, you're slowing your car down. Every Class racer and professional racing team looks to minimize rotating mass!

You might consider a Denny's HD aluminum driveshaft, or Mark Williams.

Since i'm building my car into a Stock Eliminator ride, and an aluminum driveshaft is illegal in my class (F/SA 295HP/350 67' camaro) i regretfully put a Nitrous Ready Steel shaft in my car which weighed 7lbs more then the stock one!

98tadriver
06-24-2006, 12:30 PM
Ill have to make up for it with some weld prostars in the future then, lol

4 hundreths isnt too bad for me, i thought it was gonna be like 4 tenths

sacraficing .004 of a second for reassurance that my shaft wont twist or snap is well worth it IMO.

Tru2Chevy
06-24-2006, 12:39 PM
Ill have to make up for it with some weld prostars in the future then, lol

4 hundreths isnt too bad for me, i thought it was gonna be like 4 tenths

sacraficing .004 of a second for reassurance that my shaft wont twist or snap is well worth it IMO.

It's actually 0.04, not 0.004....but not much either way.

- Justin

BMF
06-24-2006, 02:59 PM
not much depends on how much you've spent previously to find .04 :smile:

Tru2Chevy
06-24-2006, 03:49 PM
not much depends on how much you've spent previously to find .04 :smile:

Very true....not much in the sense that we are talking about a mid 12 second street car that only races for fun. :)

- Justin

98tadriver
06-24-2006, 04:15 PM
It's actually 0.04, not 0.004....but not much either way.

- Justin


whoops, added an extra zero in there, lol

bad64chevelle
06-24-2006, 04:33 PM
Hah, with my luck I would do this and run 12.03....and then be even more pissed that had I used my aluminum DS i woulda run 11.99

Brando56894
06-25-2006, 12:56 AM
i was thinkin about switching mine out but since it doesnt seem to make that much of a difference, i might just pass it up and put the +/- $100 to something else

Ian
06-25-2006, 11:02 PM
brandon, why would you need a stronger/lighter ds?

qwikz28
06-25-2006, 11:24 PM
brandon, why would you need a stronger/lighter ds?
i think hes goin for a lighter one

bad64chevelle
06-25-2006, 11:34 PM
I sure as hell cant wait to get the 4speed in the Chevelle and tear my DS to pieces....

Ian
06-26-2006, 12:05 AM
I sure as hell cant wait to get the 4speed in the Chevelle and tear my DS to pieces....

you can reuse your driveshaft with the 4 speed?!?!

bad64chevelle
06-26-2006, 12:09 AM
I am 98% sure it will be the correct length. I have the new yoke (sp?) though for my driveshaft. I also have to get solid UJoints. I know the Muncie and TH350 had the same length DS and From what I understand a Muncie and a ST10 are the same length.

Brando56894
06-26-2006, 12:32 AM
i think hes goin for a lighter one

:nod: just for weight reduction but if it doesnt really do anything except shave off .004 then its not worth it in my book...

Tru2Chevy
06-26-2006, 01:16 PM
:nod: just for weight reduction but if it doesnt really do anything except shave off .004 then its not worth it in my book...

As posted before, it's 0.04, not 0.004. It's basically a half of a tenth. And $100 is too much to pay. I got mine for $50 :)

- Justin

Savage_Messiah
06-26-2006, 01:45 PM
As I was once told, worry about ounces and the pounds will come.

98tadriver
06-26-2006, 04:05 PM
As I was once told, worry about ounces and the pounds will come.

Did you hear that from half baked or cheech and chong? lol

Tru2Chevy
06-26-2006, 05:20 PM
Did you hear that from half baked or cheech and chong? lol

No, that was from our other fearless admin - The Weight Nazi

- Justin

Savage_Messiah
06-26-2006, 05:32 PM
OK fine I heard it twice... I dont remember if Craig or Tim was the first to say it to me tho :scratch:

BMF
06-26-2006, 07:41 PM
A smart person told you that, hehe. If the difference from 11.03 and 10.99 was a driveshaft you'd kill to have it.

I'd much rather have .04 in my favor then working against me.

bad64chevelle
06-26-2006, 08:16 PM
If the difference from 11.03 and 10.99 was a driveshaft you'd kill to have it.
:werd: like I said, that would be my luck.

Brando56894
06-27-2006, 01:12 AM
As posted before, it's 0.04, not 0.004. It's basically a half of a tenth. And $100 is too much to pay. I got mine for $50 :)

- Justin

oh in that case yea if its .04 not .004 then thats alot better

Injuneer
06-30-2006, 03:30 PM
Dyno test of stock steel vs. 1LE aluminum DS:

http://www.ws6.com/mod-1.htm

Brando56894
06-30-2006, 10:30 PM
interresting...

WildBillyT
07-12-2006, 07:47 PM
I am 98% sure it will be the correct length. I have the new yoke (sp?) though for my driveshaft. I also have to get solid UJoints. I know the Muncie and TH350 had the same length DS and From what I understand a Muncie and a ST10 are the same length.

As long as the output splines are the same for both trannys. I seem to remember the ST10 and Muncie using a TH400 yoke...