Now that Franks' is no more, where do I go for custom exhaust

[alamantia]

I have a 1992 Full Size blazer with a dual custom exhaust that must have been installed by the previouls owner, thing is, it was regular steel or aluminized steel and its resembeling a cheese grader right about now. I want to cut out the current system, buy a new stainless steel cat and mufflers and bring it to someone around here to have them bend up two stainless steel pipes and hang them for me. Problem is i dont want to bend over and take it to have this done. Anyone do good work in Bergen county area who isnt too pricy? I have heard there is a place on Franklin Tpk in the ramsey/mahwah area. I have also heard the Midas on 17north in Ramsey will do custom work too. Any suggestions?

[qwikz28]

that midas on 17 north is diesel. i would check them out

[alamantia]

yeah, that midas did a dual system for my brothers suburban back in the day after he replaced the 350 with a 454 and headers.

i hear this guy does real good work too

http://www.kcscustomexhaust.com/

[qwikz28]

wow that place is really close to me! i might have to run over there and check it out. i pass by it every week and never noticed it... interesting

[Knipps]

yeah, that midas did a dual system for my brothers suburban back in the day after he replaced the 350 with a 454 and headers.

i hear this guy does real good work too

http://www.kcscustomexhaust.com/

idk about pricing and whatnot but when my trans died he turned me away b/c he said he didn't do them anymore but was a really cool guy

a friend of mine knows the guy and KC knows what he's doing

[bubba428]

dude go to petersons in egg harbor city...they made my 3.4 sound like a ls1 at idle...but its aluminized steel and all welded assembly...bad ass all around

[alamantia]

wow that place is really close to me! i might have to run over there and check it out. i pass by it every week and never noticed it... interesting



yeah, i'll be there around 9am saturday getting an estimate for a stainless dual for my blazer. If you happen to see my truck out there say hi if you like im always down with meeting peps on the site, did you happen to see the blue 3rd gen camaro for sale on North central in Ramsey near the Mac Arther / 17 interchange, by that home heating oil place, its been there for a while, i wonder what he wants for it, it looks clean, maybe its a 6cyl $1000 maybe??? i may go look at it afterwards

[bubba428]

petersons will do it for $350

[alamantia]

petersons will do it for $350

I will keep that in mind, however A/C aint exactly next door ya know, it would cost me $100 in gas and $1000 in gambeling, lunch and strippers in A/C while I wait for it to be fabricated

I do wonder if I could get a quote on-line with this info though, i dont know how well the PDF I drew up comes out but if you can see it, im sure someone could formulate me a quote off of it.

If you can open the PDF you will see the truck currently has a custom welded Y-pipe after the cat going to 2 mufflers which i can immagine is expensive to make that y-pipe, my proposed way uses a single in dual outtlet stainless muffler....

http://store.summitracing.com/partdetail.asp?autofilter=1&part=MPE%2D94109CA&N=700+115&autoview=sku

http://store.summitracing.com/partdetail.asp?autofilter=1&part=WLK%2D17519&N=700+115&autoview=sku

[NJSPEEDER]

www.mufflex.com :)

[qwikz28]

I will keep that in mind, however A/C aint exactly next door ya know, it would cost me $100 in gas and $1000 in gambeling, lunch and strippers in A/C while I wait for it to be fabricated

I do wonder if I could get a quote on-line with this info though, i dont know how well the PDF I drew up comes out but if you can see it, im sure someone could formulate me a quote off of it.

If you can open the PDF you will see the truck currently has a custom welded Y-pipe after the cat going to 2 mufflers which i can immagine is expensive to make that y-pipe, my proposed way uses a single in dual outtlet stainless muffler....

http://store.summitracing.com/partdetail.asp?autofilter=1&part=MPE%2D94109CA&N=700+115&autoview=sku

http://store.summitracing.com/partdetail.asp?autofilter=1&part=WLK%2D17519&N=700+115&autoview=sku
LOL!!!! let me know how the new exhaust comes out :)

www.mufflex.com :)
mufflex is actually terrible... i've never seen a place that half-asses so many jobs and has the audacity to charge premium prices. and even worse, the customer service is horrible. they workers there are a bunch of unprofessional jerks. i wish to never have to set foot in that place and many members on this board will agree with me. i'd actually rather make an exhaust out of home depot guttering and JB weld

[Mike]

LOL!!!! let me know how the new exhaust comes out :)


mufflex is actually terrible... i've never seen a place that half-asses so many jobs and has the audacity to charge premium prices. and even worse, the customer service is horrible. they workers there are a bunch of unprofessional jerks. i wish to never have to set foot in that place and many members on this board will agree with me. i'd actually rather make an exhaust out of home depot guttering and JB weld

a couple of the unprofesional jerks are friends of mine, and even before they worked there ive never been anything but happy when ive left the place..
so the 15-30 transactions ive had with them have been thumbs up...

[qwikz28]

a couple of the unprofesional jerks are friends of mine, and even before they worked there ive never been anything but happy when ive left the place..
so the 15-30 transactions ive had with them have been thumbs up...

the 3 or 4 i've had there were absolutely terrible. but to each their own, maybe its me i guess

[Teds89IROC]

I ordered my mufflex ORY online and when I got it a few of the pieces I had to take to meineke to have stretched out a little bigger to make them the slip fit they were suppose to be.

[alamantia]

getting done right now.. pick it up at noon... im psyched

[alamantia]

sooooooooooooooooo nice!!!!

he did a great job

[qwikz28]

any pics or anything? i might stop there one day and see what he says about making my a y-pipe or something

[alamantia]

not yet, too cold and my dads shop was so busy today being the holiday i didnt have a rack to put it up on... despite it not being mandrel bent its still ****ing ****