TTPMatt
12-29-2007, 08:53 AM
1998 Chevrolet Camaro Z28
Bright Green Metallic (Paint has some dings, some chips - front bumper clip needs paint)
Everything has less than 9 passes on them, except the rods were used in another motor for 8 passes. EVERYTHING was bought brand new including the block, starter, etc. unless otherwise noted
TTP Built 417ci Hi-Comp Race Motor
- GRP STD 1000 Aluminum Connecting Rods (17 passes on rods)
- Callies Racemaster 4.000 Crank
- Manley Lightweight -4cc Forged Pistons 4.068"
- King Rod Bearings
- Clevite Main Bearings
- GM Cam Bearings
- Machine Work completed by P&W Machine in Whippany, NJ
- Motor assembled by TTPerformance
- ARP Main stud Kit
- ARP Head Bolt Kit
- GMPP Hi-Rev Lifters
- Melling Select Oil Pump
- LS2 Double Roller Tchain
TTP Stage 4R AFR 225cc Heads
- 20+ hours of hand port/polish work on top of the AFR CNC process
Edelbrock Victor JR Intake
- 8+ hours of hand port/polish work
Barry Grant 1000CFM Race Demon Carburetor (Have jet changes 2 up 2 down)
TTP Annihilator Camshaft 262/270 .595 lift 112+2
- GM 1.7 rockers, can upgrade to 1.8 or 1.85's
Kooks 1 7/8 to 2 Stepped Longtube Headers
TTP Custom X-Pipe 3.5 into 3" with Spintech Mufflers (This system has been around for 4+ years, seen its better days, it is rusty but works fine)
Hughes Th350 trans
- Modified with JW UltraBell SFI Bellhousing
- Transbrake Unit
- Full built for 900hp
Precision Industries Vigilante 4200 Stall Converter
B&M Pro Ratchet Shifter
Grant Steering Wheel w/ Removable Hub & TBrake Button Mounted
TTP Fuel System
- Custom Fuel Cell Mount In Rear Floorpan
- RCI 5 Gallon Cell
- Aeromotive A1000 Pump
- Aeromotive Carb Bypass Regulator
- Feed: -10AN
- Return: -8AN
- Rollover Vent
Custom trunkpan cut for wheelie bar fitment and flat surface for battery mount
Entire car is wired from start to finish. Removed all stock engine harness wiring and Jay from TTP wired the entire car including switch panel inside vehicle. The pictures I have currently do not show the finished work inside I can provide those asap.
Moroso 4-Post Batt Cutoff Switch
Rearmounted Taylor Battery Box
Exide Battery
New Starter
Used Alternator
Stock hood with 6" Aero Scoop by Harwood
Madman Dipstick/Lokar Throttle Cable/Stock A4 Pedals
TTP Parachute Mount with Stroud Super Comp Chute
TTP Pro Wheelie Bar Kit
Moser 9"
- 35 spline gundrilled/star flanged axles
- Aluminum case
- Steel Moser pro spool (9lbs!)
- 4.11s
** Just refreshed with new spool and bearings
Weld Draglites 15x4 and 15x10 (They shine nice but have deep scratches)
ARP Wheel Studs (Replaced this season)
MSD 6010 Box - Controls Timing using stock ignition
LS2 Coil Packs
Taylor 10.4mm Wires w/ NGK TR6 Plugs
Hoosier 30x10.5x15 Radial C07 Slicks (Have 15 passes on them)
Mickey Thompson ET Fronts 26"
Sportsman Cage legit to 8.50 certified in August 07 by NHRA
TTP Wheelie Bar Net
TTP Parachute Rip Cord
Katech Idle Tensioner Billet
Meziere Street Electric Water Pump
Kirkey 17" wide race seat
Kirkey black seat cover (brand new)
RCI 5 Point Harness
Autometer Ultra-Lite Series Gauges ALL Electric gauges
- 5" Tach with Shiftlite playback
- Fuel Pressure 0-15
- Water Temp
- Oil Pressure
BMR K-Member
UMI Lower Control Arms Front
BMR Rear Control Arms Non Adj
BMR Adj Rear Panhard Bar
Spohn Pro Series Drag Sway Bar
Hal QA1 Front Gen R Shocks (Just replaced)
QA1 Front Springs
Hal QA1 Rear Gen F Shocks
Stock Rear Springs
Travel Limiters
Stealth Torque Arm (Spherical Rod Ends mounted to trans xmember)
All new ball joints/tie rods this season
Looking for $22,500 priced to sell.
** Due notice some of these pics are in progress pics -- i.e. carpet not placed back, areas not painted interior, gauge wiring is not complete in pics -- Everything is 100% complete now ready to go.
** The pass made at 9.94 was fully untuned with 28 deg of timing. We bumped the timing up to 32 deg, and leaned out the air fuel mixture (Still 12.3:1 rich on the dyno). We gained another 26rwhp from the untuned to the tuned version and cleaned up a lot of things with the graph. The car now makes through the th350 554 unc rwhp and 521rwhp sae. Awesome numbers for a 417 through a th350. I would put this car around a 580rwhp number in a stick car, and remember this is still a hydraulic roller cam.
http://ttperformance.net/kerminator/DSCN1334.JPG
http://ttperformance.net/kerminator/DSCN1333.JPG
http://ttperformance.net/kerminator/DSCN1335.JPG
http://ttperformance.net/kerminator/DSCN1336.JPG
http://ttperformance.net/kerminator/DSCN1259.JPG
http://ttperformance.net/kerminator/DSCN1258.JPG
http://ttperformance.net/kerminator/DSCN1169.JPG
http://ttperformance.net/kerminator/DSCN1344.JPG
http://ttperformance.net/kerminator/DSCN1181.JPG
http://ttperformance.net/kerminator/DSCN1346.JPG
http://ttperformance.net/kerminator/DSCN1345.JPG
http://ttperformance.net/kerminator/DSCN1347.JPG
http://ttperformance.net/kerminator/IMG_1064.JPG
http://ttperformance.net/kerminator/IMG_1082.JPG
VIDEO 9.94 (http://ttperformance.net/kerminator/kerm994.MPG)
Bright Green Metallic (Paint has some dings, some chips - front bumper clip needs paint)
Everything has less than 9 passes on them, except the rods were used in another motor for 8 passes. EVERYTHING was bought brand new including the block, starter, etc. unless otherwise noted
TTP Built 417ci Hi-Comp Race Motor
- GRP STD 1000 Aluminum Connecting Rods (17 passes on rods)
- Callies Racemaster 4.000 Crank
- Manley Lightweight -4cc Forged Pistons 4.068"
- King Rod Bearings
- Clevite Main Bearings
- GM Cam Bearings
- Machine Work completed by P&W Machine in Whippany, NJ
- Motor assembled by TTPerformance
- ARP Main stud Kit
- ARP Head Bolt Kit
- GMPP Hi-Rev Lifters
- Melling Select Oil Pump
- LS2 Double Roller Tchain
TTP Stage 4R AFR 225cc Heads
- 20+ hours of hand port/polish work on top of the AFR CNC process
Edelbrock Victor JR Intake
- 8+ hours of hand port/polish work
Barry Grant 1000CFM Race Demon Carburetor (Have jet changes 2 up 2 down)
TTP Annihilator Camshaft 262/270 .595 lift 112+2
- GM 1.7 rockers, can upgrade to 1.8 or 1.85's
Kooks 1 7/8 to 2 Stepped Longtube Headers
TTP Custom X-Pipe 3.5 into 3" with Spintech Mufflers (This system has been around for 4+ years, seen its better days, it is rusty but works fine)
Hughes Th350 trans
- Modified with JW UltraBell SFI Bellhousing
- Transbrake Unit
- Full built for 900hp
Precision Industries Vigilante 4200 Stall Converter
B&M Pro Ratchet Shifter
Grant Steering Wheel w/ Removable Hub & TBrake Button Mounted
TTP Fuel System
- Custom Fuel Cell Mount In Rear Floorpan
- RCI 5 Gallon Cell
- Aeromotive A1000 Pump
- Aeromotive Carb Bypass Regulator
- Feed: -10AN
- Return: -8AN
- Rollover Vent
Custom trunkpan cut for wheelie bar fitment and flat surface for battery mount
Entire car is wired from start to finish. Removed all stock engine harness wiring and Jay from TTP wired the entire car including switch panel inside vehicle. The pictures I have currently do not show the finished work inside I can provide those asap.
Moroso 4-Post Batt Cutoff Switch
Rearmounted Taylor Battery Box
Exide Battery
New Starter
Used Alternator
Stock hood with 6" Aero Scoop by Harwood
Madman Dipstick/Lokar Throttle Cable/Stock A4 Pedals
TTP Parachute Mount with Stroud Super Comp Chute
TTP Pro Wheelie Bar Kit
Moser 9"
- 35 spline gundrilled/star flanged axles
- Aluminum case
- Steel Moser pro spool (9lbs!)
- 4.11s
** Just refreshed with new spool and bearings
Weld Draglites 15x4 and 15x10 (They shine nice but have deep scratches)
ARP Wheel Studs (Replaced this season)
MSD 6010 Box - Controls Timing using stock ignition
LS2 Coil Packs
Taylor 10.4mm Wires w/ NGK TR6 Plugs
Hoosier 30x10.5x15 Radial C07 Slicks (Have 15 passes on them)
Mickey Thompson ET Fronts 26"
Sportsman Cage legit to 8.50 certified in August 07 by NHRA
TTP Wheelie Bar Net
TTP Parachute Rip Cord
Katech Idle Tensioner Billet
Meziere Street Electric Water Pump
Kirkey 17" wide race seat
Kirkey black seat cover (brand new)
RCI 5 Point Harness
Autometer Ultra-Lite Series Gauges ALL Electric gauges
- 5" Tach with Shiftlite playback
- Fuel Pressure 0-15
- Water Temp
- Oil Pressure
BMR K-Member
UMI Lower Control Arms Front
BMR Rear Control Arms Non Adj
BMR Adj Rear Panhard Bar
Spohn Pro Series Drag Sway Bar
Hal QA1 Front Gen R Shocks (Just replaced)
QA1 Front Springs
Hal QA1 Rear Gen F Shocks
Stock Rear Springs
Travel Limiters
Stealth Torque Arm (Spherical Rod Ends mounted to trans xmember)
All new ball joints/tie rods this season
Looking for $22,500 priced to sell.
** Due notice some of these pics are in progress pics -- i.e. carpet not placed back, areas not painted interior, gauge wiring is not complete in pics -- Everything is 100% complete now ready to go.
** The pass made at 9.94 was fully untuned with 28 deg of timing. We bumped the timing up to 32 deg, and leaned out the air fuel mixture (Still 12.3:1 rich on the dyno). We gained another 26rwhp from the untuned to the tuned version and cleaned up a lot of things with the graph. The car now makes through the th350 554 unc rwhp and 521rwhp sae. Awesome numbers for a 417 through a th350. I would put this car around a 580rwhp number in a stick car, and remember this is still a hydraulic roller cam.
http://ttperformance.net/kerminator/DSCN1334.JPG
http://ttperformance.net/kerminator/DSCN1333.JPG
http://ttperformance.net/kerminator/DSCN1335.JPG
http://ttperformance.net/kerminator/DSCN1336.JPG
http://ttperformance.net/kerminator/DSCN1259.JPG
http://ttperformance.net/kerminator/DSCN1258.JPG
http://ttperformance.net/kerminator/DSCN1169.JPG
http://ttperformance.net/kerminator/DSCN1344.JPG
http://ttperformance.net/kerminator/DSCN1181.JPG
http://ttperformance.net/kerminator/DSCN1346.JPG
http://ttperformance.net/kerminator/DSCN1345.JPG
http://ttperformance.net/kerminator/DSCN1347.JPG
http://ttperformance.net/kerminator/IMG_1064.JPG
http://ttperformance.net/kerminator/IMG_1082.JPG
VIDEO 9.94 (http://ttperformance.net/kerminator/kerm994.MPG)