Tagz
10-10-2008, 07:19 PM
LT1 short block built for boost: $2800
I planned on building a turbo camaro. I started it, got along pretty far then just lost the motivation. i'm selling the short block I had built for it. The short block was in the car, and ran fro about 5 minutes. The head gaskets (Cometic) leaked coolant, so i pulled her apart and just got fed up at that point. So, my loss is your gain. Heres what its got:
LT1 Short block
Crank
Scat #435010L - 4340 Forged
$630.00
Connecting Rods
Scat #6570021 - 4340 Forged H-Beam rods
$399.95
Pistons
JE Piston #131636 - Dished -22 4.030"
$775.00
(Ring set - J100F8-4030-5)
$98.00
Main Caps
Pro-Gram #SB350C22 - 22* Splayed Main caps (3 center caps)
$226.13
Main Cap studs
ARP #ARP 234-5601
$83.95
Bearings
Main bearings: Federal Mogul #4663M - Tri metal
$26.95
Rod Bearings: Federal Mogul # 8-7100CH
$54.95
Crank Hub
Jegs #055551607 - Keyed crank hub.
$79.99
All that is worth around 2400. Those prices were taken directly off the reciepts. I also paid 2500 dollars to machine/install 4 bolt main caps, line bore, line hone, ck10 hone, deck the block, balance (done internally), and assemble the short block. So i put close to 5000 into this engine.
I am asking $2800. I'm taking a beating on it, but thats how this stuff goes. So like i said above, my loss is your gain. Post, email or PM!
right now I only have this picture, if you want more let me know.
http://204.15.8.5/~tagz/engine1.jpg
Rathershort@gmail.com
I planned on building a turbo camaro. I started it, got along pretty far then just lost the motivation. i'm selling the short block I had built for it. The short block was in the car, and ran fro about 5 minutes. The head gaskets (Cometic) leaked coolant, so i pulled her apart and just got fed up at that point. So, my loss is your gain. Heres what its got:
LT1 Short block
Crank
Scat #435010L - 4340 Forged
$630.00
Connecting Rods
Scat #6570021 - 4340 Forged H-Beam rods
$399.95
Pistons
JE Piston #131636 - Dished -22 4.030"
$775.00
(Ring set - J100F8-4030-5)
$98.00
Main Caps
Pro-Gram #SB350C22 - 22* Splayed Main caps (3 center caps)
$226.13
Main Cap studs
ARP #ARP 234-5601
$83.95
Bearings
Main bearings: Federal Mogul #4663M - Tri metal
$26.95
Rod Bearings: Federal Mogul # 8-7100CH
$54.95
Crank Hub
Jegs #055551607 - Keyed crank hub.
$79.99
All that is worth around 2400. Those prices were taken directly off the reciepts. I also paid 2500 dollars to machine/install 4 bolt main caps, line bore, line hone, ck10 hone, deck the block, balance (done internally), and assemble the short block. So i put close to 5000 into this engine.
I am asking $2800. I'm taking a beating on it, but thats how this stuff goes. So like i said above, my loss is your gain. Post, email or PM!
right now I only have this picture, if you want more let me know.
http://204.15.8.5/~tagz/engine1.jpg
Rathershort@gmail.com