LT1 car to LS1 swap

[DevilDougWS6]

anyone have any experience or knowledge on this? I am about to swap an LS1 from a 2002 firehawk into a 94 camaro.

i just need some insight as to what is involved. do i have to replace the k-member, how is the wiring harness setup etc.

any info is appreciated!

[BonzoHansen]

I have an LS1 k member if you need it.

[NJ346]

anyone have any experience or knowledge on this? I am about to swap an LS1 from a 2002 firehawk into a 94 camaro.

i just need some insight as to what is involved. do i have to replace the k-member, how is the wiring harness setup etc.

any info is appreciated!

If this is for sam what's the matter with the cammed Lt1 that's in there?

[ar0ck]

K-Member and accessory bracket are what come to mind that are most important.

[BonzoHansen]

K-Member and accessory bracket are what come to mind that are most important.

accessory bracket?

[DevilDougWS6]

vin: it is not for sam, i dont know what is wrong with her lt1, if anything at all, besides the rear. i am taking the motor from her firehawk though.

and i may need the k-member, i have to check out the condition of the one from the donor car because it was hit on the front end.

[LTb1ow]

I think new springs cause the motor will be lighter. Not sure though.

[NJ346]

vin: it is not for sam, i dont know what is wrong with her lt1, if anything at all, besides the rear. i am taking the motor from her firehawk though.

and i may need the k-member, i have to check out the condition of the one from the donor car because it was hit on the front end.

Nice. Good luck with the swap. Check over on Ls1tech, I'm sure they have a lot of info on these swaps, I've seen a few done over there.

[BonzoHansen]

vin: it is not for sam, i dont know what is wrong with her lt1, if anything at all, besides the rear. i am taking the motor from her firehawk though.

and i may need the k-member, i have to check out the condition of the one from the donor car because it was hit on the front end.

I will trade it for 2 6-packs of Magic Hat HIPA (http://ontap.files.wordpress.com/2007/03/hipa-copy.jpg).

[deadtrend1]

I think new springs cause the motor will be lighter. Not sure though.

correct ...

[DevilDougWS6]

im going to check out this k-member, the only thing it LOOKS like it needs is maybe the lower a-arm and definitely needs a tie rod end.

and since we are swapping the entire k-member/engine/trans, can't i just keep the springs in there.

[Mike]

im going to check out this k-member, the only thing it LOOKS like it needs is maybe the lower a-arm and definitely needs a tie rod end.

and since we are swapping the entire k-member/engine/trans, can't i just keep the springs in there.

yes springs, shocks, spindles could all stay...

[LTb1ow]

I suppose that would mean LS1 style brakes in the back too, right?

[MonmouthCtyAntz]

Search on tech theres alot of info on this, I could also ask the guy who did mine.

[BlackBADaSS02]

I was looking into doing this, but sold the project to my brother before I got around to finishing it.
At minimum, you would need a K member & LS1 steering rack and linkage. Speartech can modify the engine harness to be plug and play in an LT1 car. Also, it would be a good idea to upgrade the fuel pump. You can keep the LT1 fuel system if you use a corvette fuel presure regulator. That gets you out of changing to an LS1 fuel system. Tech has a lot of information on this swap. Just do a search, and you'll come up with a lot of information.

[DevilDougWS6]

yup. thanks guys. i found a LOT of info on tech, pretty much everything i need hopefully.

[01blackz28]

doug give sick speed performance a call. they swapped a 2000 ls1 into my 94 chassis. Need kemember and a modified ecu.

[Mike]

doug give sick speed performance a call. they swapped a 2000 ls1 into my 94 chassis. Need kemember and a modified ecu.

you wouldnt really need to modify the ecu, if you have the computer and full harness that the engine and trans came out of........

[sweetbmxrider]

I suppose that would mean LS1 style brakes in the back too, right?

why?

[LTb1ow]

Wouldn't running LS1 ABS system require a 4 channel rear?

[Mike]

you could probably save the lt1 style abs...at that point you might have to modify the harness

[LTb1ow]

Ah yea, I guess they are separate computers right?

[DevilDougWS6]

well this car is getting a complete drivetrain swap motor/trans/and rear.

[1984camaroz28]

We have done a few of thes swaps heres the run down of everything that neeeds to be changed. You can have your stock LSx wiring harness modified so its a direct plug in to the 94 body hanress Spertech does this for 500$ well worh it. The fuel systems are the same just run a regulator to set you fuel presure. You will f course need a ls k member. The onethng that wont work is the gasg gauge you will need to buy a autolite gauge. Also the stock LS1 air box system will NOT clear a lt1 hood you will need to run a lt1 style system

[MonmouthCtyAntz]

Also the stock LS1 air box system will NOT clear a lt1 hood you will need to run a lt1 style system
Even though I run a LTx style airbox you can run a Ls1 system.


http://i113.photobucket.com/albums/n226/Antz97znj/merv1.jpg
http://i113.photobucket.com/albums/n226/Antz97znj/merv2.jpg
http://i113.photobucket.com/albums/n226/Antz97znj/merv3.jpg
http://i113.photobucket.com/albums/n226/Antz97znj/merv4.jpg

[NJSPEEDER]

have a close up of how the airbox and lid are modified to fit? It has to be cut way down to clear the hood.

[MonmouthCtyAntz]

http://www.ls1tech.com/forums/lt1-lt4-modifications/1071121-ls1-lid-conversion.html