4L60E for Sale Cheap!!!

[ZCarr]

I have a rebuilt trans with only 50K on it for sale for $200.00 or best offer.

[Camarokid08731]

what converter?

[S.J.SLEEPER]

what year is it out of?

[ZCarr]

Stock Converter and it is out of a 1994

[S.J.SLEEPER]

you need to let people know that this is for lt1 & down cars.
your trans has a 298mm stator
the 98-02 fbody & trucks w/ ls style engine have 300mm stator

not being a dick, just tryin to help you out so you don;t get a million questions about it.

[97ws6]

If it will fit a 97 formula Im interested. PM me the part number.

[ZCarr]

I will send you the part number when I get home.

[S.J.SLEEPER]

if its out of a 93-97 lt1 car then it will fit

[LTb1ow]

Fit yes, but weren't the early years 4L60 not the later years 4L60E?

[S.J.SLEEPER]

93-97 4l60e in the fbodys are the same guts & shell
i beleive the splits are 93-94 95 & 96-97
& the differneces is the electronics which can be changed.
(remove pan, change solenoids & harness out of old one to new one.)

[Tru2Chevy]

93 was 4L60, 94-97 was 4L60e

The '94 trans for sale here will fit the '97 Formula in question with no problems unless the '94 trans was for the 3.4L (since the OP didn't specify).

- Justin

[97ws6]

Ok if it fits 97 I want it. I am sending you a PM.

[97ws6]

Whats going on? You selling this or not?

[sweetbmxrider]

IIRC, 94 is the goofball year (typical lt1) and will only fit 94s.....

[deadtrend1]

IIRC, 94 is the goofball year (typical lt1) and will only fit 94s.....

HMMM? Not to my knowledge. Only 93 used a 700R4 (kickdown cable), then 94 and up used 4L60E

[sweetbmxrider]

To put a ’96 4L60E into a ’94 car: The ’94 tailshaft housing and VSS must be installed on the ’96 4L60E before the trans can be bolted into the car. Mod A must be performed. The trans will operate normally without Mod A but TCC lockup will not work, so highway and cruising gas mileage will suffer and more heat will be produced in the transmission.

TCC Mod (method 1):
An additional wire must be run from the PCM connector D pin 6 to pin "U" on the trans harness for the TCC to work. Also, the PCM must be reprogrammed with ’95 transmission base code. In my opinion this is more work than its worth due to the amount of labor involved in properly routing an additional wire into the powertrain wiring harness.

TCC Mod (method 2):
Leave the PWM solenoid unplugged but installed. On the valve directly to the right of the PWM solenoid – push that valve all the way towards the outside of the valvebody, and stake it into place. That’ll lock keep the valve acted on by the PWM in the full-open position and it’ll function like a '94 style lockup. No PCM reprogramming required. Now with pics! You may have to swap the ’94 internal harness into '95-’96 transmission, but I'm not sure. I recommend not swapping harnesses if you don't have to, because they will most likely be brittle and are tricky to remove from the case without damaging the lugs on the connector.

for what its worth

"mod a"

http://www.impalassforum.com/vBulletin/showpost.php?p=2168806&postcount=12

[97ws6]

Well I wanted to put it in a 97, but no matter, this guys doesnt answer PM's or update his posts. I will find another one, there are plenty out there.

[sweetbmxrider]

i would consider 97 the same as 96 in reference to that article....

[ZCarr]

I responded to your pm. I am sorry for the delay in getting back you I had a death of a long time friend of the family.

[V]

do you know if id be able to put the tailhousing from a 4wd 4l60e onto this 2wd one and use it in a 96 4wd tahoe? if so im very interested

[ZCarr]

ttt

[Rich2279]

Location in NJ?

[ZCarr]

South Jersey right off of exit 2.

[ZCarr]

ttt

[twokss]

where are you off exit 2? i live half a mile from there

[ZCarr]

Woodstown. You?

[twokss]

mullica hill...322

[ZCarr]

ttt

[siguy]

you have a pm

[siguy]

for what its worth

"mod a"

http://www.impalassforum.com/vBulletin/showpost.php?p=2168806&postcount=12


dumb question why not just swap the hole valve body from the old transmission to the one being used with the wiring harness wouldn't that be easyer?