emolineaux
07-31-2012, 05:51 PM
Ill be in NJ tomorrow to saturday morning! pm or text me if interested and ill bring title up with me. (leaving nc around 12am) if not its going to be off the market once i haul all the parts back with me that are sitting around.
i have my 1988 ford f250 custom 4x4 up for sale.
currently isnt running due to needing some parts installed (have all parts but the belt and fluids)
truck is a standard cab long bed, dual gas tanks has 33 inch wrangler mtz tires along with an aftermarket trailer hitch.
the original 351 was beat so that was replaced with a 5.0 high output out of a 90 lincoln mark vii
has some dings and dents on body from over the years. and some slight surface rust on hood and roof. no major rot like most older ford trucks have.
i have alot of money into new parts and have a list of all new parts ive done to truck.
looking for a cash deal or trade (please no street bikes or atv trades) interested in rwd muscle cars (v6 or 4 cyl RWD american cars are ok)
not looking for anything specific so let me know what you have to offer.
list of new parts installed and included with sale of truck
5.0 H.O. engine (90k miles)
pasesetter shorty headers
magnaflow y pipe with cat ( needs band clamp or welded as i had to shorten mid section to work with narrower 5.0 engine)
flowmaster catback single exit exhaust
Radiator
Water pump
radiator hoses
thermostat
f250 5.0 egr tube
f250 5.0 oil pan
f250 5.0 high volume oil pan and pickup tube
f250 5.0 oil pump drive
ford racing aluminum valve covers
ford racing spark plug wires
motorcraft oil filter
motorcraft spark plugs
motorcraft fuel filter
5.0 upper and lower intake manifold (cleaned and painted)
roll pan rear bumper
fuel injector o-rings
slave cylinder
slave cylinder line
clutch
flywheel
brake master cylinder
duralast gold top battery
what still needs to be finished for it to run
install front and rear drive shafts
drill holes in new ears welded to trans to mount to trans mount
bolt trans crossmember to frame
install tcase handle
install slave cylinder fluid line
install starter
install exhaust
install battery
might of forgot a few items but thats most of it.
$1700 obo
would be more open to a trade deal for a rwd american car. mid 90s or older muscle cars are prefered but v6 and 4 cyl model or roller muscle cars are ok to. not set one one car so let me know what ya have!
contact me via text any time
6099709899
Eric
(bed on passanger side is in primer black. as i started some body repair)
http://i11.photobucket.com/albums/a158/jankenson/267226_2327999598616_1208460673_4495341_2175084_n. jpg
5.0 High Output before it went into the truck
http://i11.photobucket.com/albums/a158/jankenson/419472_3600984782450_1520680901_n.jpg
http://i11.photobucket.com/albums/a158/jankenson/378847_3067333161493_1185118932_n.jpg
http://i11.photobucket.com/albums/a158/jankenson/409717_3612989762567_299212843_n.jpg
i have my 1988 ford f250 custom 4x4 up for sale.
currently isnt running due to needing some parts installed (have all parts but the belt and fluids)
truck is a standard cab long bed, dual gas tanks has 33 inch wrangler mtz tires along with an aftermarket trailer hitch.
the original 351 was beat so that was replaced with a 5.0 high output out of a 90 lincoln mark vii
has some dings and dents on body from over the years. and some slight surface rust on hood and roof. no major rot like most older ford trucks have.
i have alot of money into new parts and have a list of all new parts ive done to truck.
looking for a cash deal or trade (please no street bikes or atv trades) interested in rwd muscle cars (v6 or 4 cyl RWD american cars are ok)
not looking for anything specific so let me know what you have to offer.
list of new parts installed and included with sale of truck
5.0 H.O. engine (90k miles)
pasesetter shorty headers
magnaflow y pipe with cat ( needs band clamp or welded as i had to shorten mid section to work with narrower 5.0 engine)
flowmaster catback single exit exhaust
Radiator
Water pump
radiator hoses
thermostat
f250 5.0 egr tube
f250 5.0 oil pan
f250 5.0 high volume oil pan and pickup tube
f250 5.0 oil pump drive
ford racing aluminum valve covers
ford racing spark plug wires
motorcraft oil filter
motorcraft spark plugs
motorcraft fuel filter
5.0 upper and lower intake manifold (cleaned and painted)
roll pan rear bumper
fuel injector o-rings
slave cylinder
slave cylinder line
clutch
flywheel
brake master cylinder
duralast gold top battery
what still needs to be finished for it to run
install front and rear drive shafts
drill holes in new ears welded to trans to mount to trans mount
bolt trans crossmember to frame
install tcase handle
install slave cylinder fluid line
install starter
install exhaust
install battery
might of forgot a few items but thats most of it.
$1700 obo
would be more open to a trade deal for a rwd american car. mid 90s or older muscle cars are prefered but v6 and 4 cyl model or roller muscle cars are ok to. not set one one car so let me know what ya have!
contact me via text any time
6099709899
Eric
(bed on passanger side is in primer black. as i started some body repair)
http://i11.photobucket.com/albums/a158/jankenson/267226_2327999598616_1208460673_4495341_2175084_n. jpg
5.0 High Output before it went into the truck
http://i11.photobucket.com/albums/a158/jankenson/419472_3600984782450_1520680901_n.jpg
http://i11.photobucket.com/albums/a158/jankenson/378847_3067333161493_1185118932_n.jpg
http://i11.photobucket.com/albums/a158/jankenson/409717_3612989762567_299212843_n.jpg