1320B4U
09-07-2012, 01:51 PM
These are the ultra rare and hard to find original ronal r-15 wheels that came on the 1992 Firehawk (german made). It took me a long time to source these wheels for my firehawk clone i put together. After the car was sold i kept the wheels thinking i might use them down the road. They measure 17x9.5" (x4 wheels) (17x9.5 = 5 x 120.65mm)and run a 275/40z17 inch tire on new (less than 2k miles) rapture tires. Rims have no curb damage and are straight and true. I had rims painted original wa8774 'pontiac red' when the car was resprayed late last year...triangle faces and inside of rims painted at that time just like the original firehawk came with. Ronal has started making a limited run of these wheels again after several years of stating so and a complete set costs upwards of $1400 w/out tires.
These rims WILL fit a brembro big brake upgrade on a 3rd gen and by the looks of it will fit on my camaro that runs a baer track setup.
What is included::
4 ronal wheels (offset's are different front to back but width of rim is the same)
4 original center caps w/'ronal' emblazened on them w/locking face screws
4 rapture tires in size stated above (nubs still on sidewall of tires)
4 locking lug locks and key
2 original front wheel spacers (which you cannot get from summit)
2 rear generic spacers (to keep the track identical to the front)
10 extended lug nut studs (dorman 12-1.5x54 tahoe studs)..i chose to install these as precautionary b/c i ran an additional 2mm spacer up front.
Have these listed for $1250 on c/l but njfboa members $1150...counting tires and paint i have almost 2k in these.
This is a complete bolt in setup..nothing else is needed and is 1 of the widest size tires to fit on a 3rd gen (front). Condition from 1-10 (10 being best) is probably a solid 8.5...some minor clear code haze on parts of rims but nothing serious at all. 1 rim has a run in the spray job as well (never did wet sand it down).
-dave 646.772.0237
http://i678.photobucket.com/albums/vv143/B1320B4U/IMG00313-20120603-1147.jpg
http://i678.photobucket.com/albums/vv143/B1320B4U/truck.jpg
http://i678.photobucket.com/albums/vv143/B1320B4U/wheels1.jpg
http://i678.photobucket.com/albums/vv143/B1320B4U/wheels.jpg
These rims WILL fit a brembro big brake upgrade on a 3rd gen and by the looks of it will fit on my camaro that runs a baer track setup.
What is included::
4 ronal wheels (offset's are different front to back but width of rim is the same)
4 original center caps w/'ronal' emblazened on them w/locking face screws
4 rapture tires in size stated above (nubs still on sidewall of tires)
4 locking lug locks and key
2 original front wheel spacers (which you cannot get from summit)
2 rear generic spacers (to keep the track identical to the front)
10 extended lug nut studs (dorman 12-1.5x54 tahoe studs)..i chose to install these as precautionary b/c i ran an additional 2mm spacer up front.
Have these listed for $1250 on c/l but njfboa members $1150...counting tires and paint i have almost 2k in these.
This is a complete bolt in setup..nothing else is needed and is 1 of the widest size tires to fit on a 3rd gen (front). Condition from 1-10 (10 being best) is probably a solid 8.5...some minor clear code haze on parts of rims but nothing serious at all. 1 rim has a run in the spray job as well (never did wet sand it down).
-dave 646.772.0237
http://i678.photobucket.com/albums/vv143/B1320B4U/IMG00313-20120603-1147.jpg
http://i678.photobucket.com/albums/vv143/B1320B4U/truck.jpg
http://i678.photobucket.com/albums/vv143/B1320B4U/wheels1.jpg
http://i678.photobucket.com/albums/vv143/B1320B4U/wheels.jpg