Brown Santa came to visit...

[B4C]

And he left this...quick performance 9in, yukon nodular center, 35 spline wavetrack, 4:11's.
http://i146.photobucket.com/albums/r257/BrokeChevy/20130411_183308_zpsb7bd8fda.jpg (http://s146.photobucket.com/user/BrokeChevy/media/20130411_183308_zpsb7bd8fda.jpg.html)

[sweetbmxrider]

Follow proper gear break in!

[redsoxsstink]

guess you didnt go with the spool. hopefully this one is built better than the 12bolt. good luck with it

[B4C]

Follow proper gear break in!

Yeah definatly spent a lot on this stuff

guess you didnt go with the spool. hopefully this one is built better than the 12bolt. good luck with it

I hope so to its all new stuff from quick performance so it better be good

[WildBillyT]

Follow proper gear break in!

This. Follow their instructions to the letter.


Looks great, Mike.

[B4C]

This. Follow their instructions to the letter.


Looks great, Mike.

All their instructions say are 4-5 heat cycles 3miles each time

[WildBillyT]

Then you are good.

[B4C]

Installed the axle bearings and bolted it all together, now to install it
http://i146.photobucket.com/albums/r257/BrokeChevy/20130412_152208_zpscca1599a.jpg
The wavetrack
http://i146.photobucket.com/albums/r257/BrokeChevy/20130410_220321_zps196afd2c.jpg
How they shipped the center section
http://i146.photobucket.com/albums/r257/BrokeChevy/20130410_204403_zpsf1ae5253.jpg

[Dudbird113]

So 1000 for the rear with perches and axles and wat not. How much did the center section cost ya

[B4C]

So 1000 for the rear with perches and axles and wat not. How much did the center section cost ya

because i got the wavetrack it was 1800

[greenformula92]

looks nice

[coolmanvette75]

Exact same rear setup as mine from them except I got a spool instead of the wavetrac. The Yukon center is a nice piece. Here was my install. Only thing you should have to do is make the hole on the panhard par bracket slightly bigger

http://ls1tech.com/forums/gears-axles/1560706-quick-performance-9-mwc-t-install.html

[B4C]

Exact same rear setup as mine from them except I got a spool instead of the wavetrac. The Yukon center is a nice piece. Here was my install. Only thing you should have to do is make the hole on the panhard par bracket slightly bigger

http://ls1tech.com/forums/gears-axles/1560706-quick-performance-9-mwc-t-install.html

Yeah I heard about the panhard bolt. They were pushing the strange center but the yukon has larger bearings caps and it was the same price so I went with that one. Its all ready to go in im just busy wanting to kill myself while doing a tuneup on a thrid gen at the moment.

What hole did you use on the lca barackets? Looking to lessen my wheel hop. Its nice that they built relocation brackets in.

[coolmanvette75]

Yeah I heard about the panhard bolt. They were pushing the strange center but the yukon has larger bearings caps and it was the same price so I went with that one. Its all ready to go in im just busy wanting to kill myself while doing a tuneup on a thrid gen at the moment.

What hole did you use on the lca barackets? Looking to lessen my wheel hop. Its nice that they built relocation brackets in.

The lowest one I think...

[k_garretson23]

I used the lowest as well.

[B4C]

@coolmanvette did the rear of the car sit higher after you installed the 9in?

[spina74]

i had mine on the lowest i didn't like how it felt when hitting bumps so i went 1 up and it was better

[Slow-V6]

Isnt the lowest hole for the LCA's intended for lowered cars?

[k_garretson23]

from my understanding you want the lca to be horizontal with the ground with the suspension loaded. All cars sit differently so it may vary

[coolmanvette75]

@coolmanvette did the rear of the car sit higher after you installed the 9in?

Yes it did. Hahaha

[B4C]

Yes it did. Hahaha

Should I do the heater hose mod at the same time then?
http://i146.photobucket.com/albums/r257/BrokeChevy/20130414_190012_zps70107501.jpg
http://i146.photobucket.com/albums/r257/BrokeChevy/20130414_190022_zps537798cb.jpg