Bunch Of Parts F/S, mostly 1st and 4th gen
 

Trying to clean up. Prices are negotiable unless otherwise noted.

Grey leather 4th gen Camaro front and rear seats. Out of a 2000 Z28. Good condition, driver's front seat has a small hole on the lower right bottom part and the upper part is showing wear on the "bolster" part. Passenger and rear seats have no blemishes. $200 Sold.

Complete body harness from 2002 Z28 LS1/M6. Includes underhood fuse boxes, no engine harness Sold

Stock LS1 4th gen fan assembly, $100 Sold

Stock 4th gen Camaro HVAC controls, the part with the 3 knobs $20

Stock coolant tank from 2000 Z28 $15 OBO

Stock maplight rearview mirror(the one that goes inside the windshield) from 99 Camaro $20 OBO

PSI Conversion standalone harness for cable throttle LS1/T56 has EV6 injector connectors $400 Sold

NOS "A" note horn, correct for 1st gen Camaros and more, Delco P/N 1892164 $50

04-06 GTO A/C Compressor, came out of a low mile car that was gutted to become a race car. $55 OBO

Centerbolt valve covers for an LS engine, don't know what they originally came from. Bead blasted and clean. $60 OBO

Brand new Aerospace "Pro Street" rear disc brake kit P/N AC-530VRDSP, this is the one without parking brake. Bought it for my first gen, now going a different direction. Cross drilled, slotted, and vented rotors. This kit is over $700 from Summit with the cross drilled/slotted rotors. $550 Sold

Race version Meziere EWP for LS engines, had this on my LS2 in my 98 race car. Race version does not have a thermostat provision, and the outside part does not rotate so a regular belt will not work. This is used with low hours on it, zero street time, just dyno and track time. Also have a BMR alternator only bracket in black and the belt that works with this. Bracket was installed on my engine but never run. $275 for the pump, $350 for bracket and pump. Sold

Set of new truck coils with brackets and wiring harnesses, never run, just bolted on the engine. Ready to bolt on and run. These are the D585 coils. $150 for the set. Sold to Slow-V6

LS1 Starter, used and working but not the prettiest. $25 Sold

Carbon fiber driveshaft from my race car, had a Powerglide with rollerized tailshaft and 9". 1350 yokes, length from center of u-joint to center of u-joint is 44 5/8" asking $550 OBO local pickup only. Currently at MCP Competition Engines in Lakewood, or can be picked up in Old Bridge NJ. Sold


Everything is in Old Bridge NJ 08857 unless listed otherwise. PM or post if interested, or call me if you have my number.

More pics....

And more...

More....

Make some offers, want this stuff gone

Aerospace brake kit work on a 10 bolt? What needs to be done with the proportioning valve?

I will call Aerospace tomorrow and confirm, but I'm pretty sure it will fit a 4th gen 10 bolt. The P/N of the kit is AC-530VDRSP. I know it fits a 10/12 bolt in earlier cars. As far as the prop valve, I would run an adjustable unit to dial in the brake balance. While a 4 wheel disc brake prop valve will work, I don't think it would be optimal for an aftermarket setup like this.

Just saw you have a '69 too, I'm not sure which car of yours you were asking about fitment about but it will definitely bolt on a '69 10 bolt. I have more 1st gen stuff too, shoot me a PM with your number if you're interested.

Interested in the front seats. Sending pm

PM'd you

Coils sold.

From what the Aerospace tech told me, this kit will bolt onto pretty much any small bolt pattern 10/12 bolt, even a 7.5" rear in a g-body. By small pattern, it means everything except a full size like a Impala or truck.

Make offers, want all this stuff gone...

Updated.

Bump. Will add more this week.

Had offers on things but nobody followed through. I'm not holding on to anything from now on, so whoever shows up with cash first gets the parts. Been getting jerked around a little too much lately, and turned people away for others who never showed up or even showed the courtesy of a return call/text.

Had people asking about trades, this is stuff I need/want:

Pontiac Monsoon CD player in good working order
Polished 16" 5 spokes (Pontiac) or 17" WS6 wheels
32" or larger flat screen TV
Silver drivers side mirror, power with mount
5.3/5.7/6.0 engine, rebuildable core is fine
TH350/TH400 trans in good working order, street/strip no race stuff

Can't think of anything else right now.

Interested in the fans. I'll pm you

Updated, sold a bunch of stuff. Want the rest gone soon, make some offers.

More gone, want the rest gone soon.

More stuff gone, prices lowered on what's left.

Seats sold.

thanks for the seats artie