Today's Posts
Mark Forums Read
Calendar
NJFBOA - Home of New Jersey's Camaros and Firebirds
>
Search Forums
Search Results
User Name
Remember Me?
Password
Home
Register
FAQ
Today's Posts
Search
Notices
Unregistered, Support the Sponsors that help NJFBOA!!
Search Forums
Show Threads
Show Posts
Tag Search
Advanced Search
Go to Page...
Showing results 1 to 7 of 7
Search took
0.00
seconds.
Search:
Posts Made By:
transmaro93
Forum:
Restorations, Fabrication, Tool and Shop Tech
03-13-2013, 06:05 PM
Replies:
47
Harness through metal Question
Views:
11,066
Posted By
transmaro93
lol... so why cant he do what i said yesterday...
lol... so why cant he do what i said yesterday and just cut a small hole from the inside and a larger on in that frame peice... if it can be unplugged once trans is lowered a little... chances are...
Forum:
Restorations, Fabrication, Tool and Shop Tech
03-13-2013, 05:54 PM
Replies:
47
Harness through metal Question
Views:
11,066
Posted By
transmaro93
ok.. but is it not a bigger pain the in the ass...
ok.. but is it not a bigger pain the in the ass to remove interior every time you have to disconnect that plug. if your looking in the long run to make life easier should the trans have to come out...
Forum:
Restorations, Fabrication, Tool and Shop Tech
03-13-2013, 05:13 PM
Replies:
47
Harness through metal Question
Views:
11,066
Posted By
transmaro93
ok even with a decent sized hole cut in that...
ok even with a decent sized hole cut in that frame peice you wont be able to sneak your fingers in there to attach and detach the harness from under the car? ... if this is so what if you "notch"...
Forum:
Restorations, Fabrication, Tool and Shop Tech
03-12-2013, 06:18 PM
Replies:
47
Harness through metal Question
Views:
11,066
Posted By
transmaro93
was thinking more about this... is there an...
was thinking more about this... is there an actual clearance issue on the trans half of the connector or just a clearance issue when the harness end is plugged in? was thinking today to do it (imo)...
Forum:
Restorations, Fabrication, Tool and Shop Tech
03-11-2013, 08:33 PM
Replies:
47
Harness through metal Question
Views:
11,066
Posted By
transmaro93
if you wanna cut and weld a plate or somthing...
if you wanna cut and weld a plate or somthing that is doable to. i can help ya with that if you want to go that route. but your car is at your house and not drivable. assuming you dont have a welder...
Forum:
Restorations, Fabrication, Tool and Shop Tech
03-11-2013, 08:22 PM
Replies:
47
Harness through metal Question
Views:
11,066
Posted By
transmaro93
lol i know thats where it is but its hard to tell...
lol i know thats where it is but its hard to tell in pic how curved it is. i dont see why you can just cut a nice hole with a hole saw and use those grommets. if that ring is metal you can bang it...
Forum:
Restorations, Fabrication, Tool and Shop Tech
03-11-2013, 08:12 PM
Replies:
47
Harness through metal Question
Views:
11,066
Posted By
transmaro93
how curved is that area? those grommets are...
how curved is that area? those grommets are pretty cool. id say cut it with a holesaw put the grommet in and just bang it into place and screw it in with the supplied holes. If its not going to be...
Showing results 1 to 7 of 7
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Event Forums
NJFBOA Events
NJFBOA Meet Pics
East Coast F-Body Nationals
2010 East Coast F-Body Nationals
2009 East Coast F-Body Nationals
2008 East Coast F-Body Nationals
2007 East Coast F-Body Nationals
2006 East Coast F-Body Nationals
2005 East Coast F-Body Nationals
Cruisers' Corner / Other Events
Camaros, Firebirds and the People that own them
Welcome / Introduction
Member's Rides
The Early Years 67-92
The Later Years 93-present
Other Musclecars
Member's Projects
Stop the Presses!
Lounge
The Bounce House Link
Multimedia
SEMA Action Network and Automotive Legislation
NJFBOA Forums
Site Sponsor and Group Purchases
Club and Website Support
Regional Forums
North Jersey
West Central Jersey
East Central Jersey
South Jersey
Competition Forums
Drag Racing
Road Racing / Auto X
Racer's Lounge
General Tech
Engine / Power / Tuning
Brake, Chassis and Suspension Tech
Transmission and Driveline
Appearance
In Car Entertainment
Electrical and Wiring
Restorations, Fabrication, Tool and Shop Tech
Classified Forums
Classifieds Forums
For Sale - Automotive Parts
For Sale - Vehicles
Wanted To Buy - Automotive
Classifieds - Other
» Sponsor List
All times are GMT -5. The time now is
10:51 PM
.
Contact Us
-
New Jersey F-Body Owners Association - Home of New Jersey's Camaros and Firebirds
-
Archive
-
Top
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.