Not this again.

[Blackbirdws6]

Originally Posted by LS1ow

i wish fbody stuff came in more colors than red or black. so boring.

They can. Just need to spend the $ to get it bare/stripped and powdered to your hearts content.

[LS1ow]

Originally Posted by Blackbirdws6

They can. Just need to spend the $ to get it bare/stripped and powdered to your hearts content.

[MDSheds_SS]

Hope it helps, didn’t do **** for me. Waste of money. Mines collecting dust on the garage wall.

[sweetbmxrider]

If it was red, white, and blue......1.0x

[LS1ow]

Originally Posted by MDSheds_SS

Hope it helps, didn’t do **** for me. Waste of money. Mines collecting dust on the garage wall.

i wish i knew this. i would have bought it

[LS1ow]

Fancy dual swivel end -4 hose for nitrous fuel feed came in yesterday. Pretty much the last piece of the puzzle. Other than the blow down tube... which i seem to have lost.

[Jersey Mike]

You havent heard of spray paint? One guy made his trans pan pink. Where there's a lulz there's a way

[Jersey Mike]

Also I have a blow down tube still in the packaging. Amazon 2 Day may be faster than you driving to the suburbs but if you want it let me know and I'll leave it out for you

[LS1ow]

took a page out of the book of kohler, and used the inner fender well and random holes in frame to run feed line. It comes from the bottle, through the rubber grommet in the rear seat well, ran along the pinch weld with wire holders,then up the fender well secured with wire holders as well. Currently i have it coming in to the bay were the LT1s have the fuel lines(i think) coming in.

Eventually, which will prob be before the car sees the track, i would like to get a shorter feed line. I dont like how it runs across the bay from the tower to to the intake, but if i ran it the way i wanted to originally, i would have a ton of line coiled up. Which i figured is a bad thing.

[LTb1ow]

Be careful on the turn where it comes into the engine bay. Secure the line, or grommet it well.

[Blackbirdws6]

Please remove the leaf sitting in the door please. Thanks.

[LS1ow]

Originally Posted by LTb1ow

Be careful on the turn where it comes into the engine bay. Secure the line, or grommet it well.

grommet is en route from prime.

Originally Posted by Blackbirdws6

Please remove the leaf sitting in the door please. Thanks.

nope, just gunna paint it black

[Blackbirdws6]

Originally Posted by LS1ow

nope, just gunna paint it black

You'll need the weight savings.

[LS1ow]

Short of a vacuuming, bottle mounting and stuff is done. Which exception of the blow down tube, bc missing.

Window Switch and progressive controller mounted on the side of the bottle bracket for easy access of use. Ran feed line through the cup holder to avoid any crazy bends in the line. Figured may as well run the wires for the heater pressure sensor there as well. Loomed everything the best i could. There is a ton of wires in a small area, all of which are going different ways. so its a bit sloppy. May redo at some point, but good enough for now. Going to get a small piece of PVC and cut it in half long ways to create like a tunnel for the wires that run under the console, and then recarpet over it. As you can see i cut off to much carpet between bottle mount and console.

[LTb1ow]

Looks pretty race car

[Blackbirdws6]

Nitrous plumbing/wiring seems to always be a bit messy so don't feel bad. Access to the important stuff looks good and it will work so keep it moving.....and yes, please vacuum the area.

[sweetbmxrider]

I'd run a couple more beads of weld on the intake. Nice job brah.

[Jersey Mike]

I like that console idea. Those rear cupholders are ****ing useless.

[LS1ow]

Everything is pretty much done. However i do think a hardline may be in order instead of the black AN for the fuel. Should look much better once i put everything else back together. Such as the harness and catch can wires that are just sphaggeti'd everywhere

[Jersey Mike]

Who are you and what have you done with the Beggs I knew

[LS1ow]

Originally Posted by Jersey Mike

Who are you and what have you done with the Beggs I knew

Oh you just wait.

[sweetbmxrider]

Hardline would look good there and on the purge.....Too bad you didn't invest in the mastercool flaring kit with -an dies

[LS1ow]

Originally Posted by sweetbmxrider

Hardline would look good there and on the purge.....Too bad you didn't invest in the mastercool flaring kit with -an dies

Purge is hardlined, it’s just wrapped in wire loom Bc the line isn’t the same color or the plate lines

[sweetbmxrider]

[LS1ow]

Originally Posted by Jersey Mike

Who are you and what have you done with the Beggs I knew