Today's Posts Mark Forums Read Calendar
Go Back   NJFBOA - Home of New Jersey's Camaros and Firebirds > Tech Forums > General Tech

Notices


View Poll Results: Which is best
Engine/Trans/Subframe together 10 100.00%
Engine/Subframe only 0 0%
Voters: 10. You may not vote on this poll

Reply
 
Thread Tools
Old 08-08-2017, 04:40 PM   #1
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Motor Swap Toss up

The time is coming. So lettuce wiegh out some options.

Pretty much, im in a toss up on how to assemble this pig. Do i mate the trans together with the engine and front end? or do i throw the front end w. motor in by itself and do the trans on my back? Lets take a closer look cotton...


Engine/Front End/Trans-


-First and formost... time due to cost. I cant mate the engine and trans together without throwing the stall converter in, and thats $800 i dont have right now. So realistically, i wouldnt be able to throw it together until after labor day weekend when i get home from Vaca. Thats an extra 4 weeks of down time.

-On the postive side, if i do wait it out it would be much eaiser to slap it together on the floor of my garage. Converter bolts to flexplate would be a breeze, and bellhousing to block would take 2 seconds. Then id roll it all under on a dolley as one.

-Drawback 2... Since the rear of the car would be on the ground, and i have large belly, the transmount wouldnt be able to be bolted in until the subframe and suspension were in and i would then be able to get the car on jack stands to do under it and throw the transmount on. So the trans would be held up on nothing but the bell housing bolts and the converter.

Engine + Front end only

The only real negative i see to this is the opposite of what i listed above. Ive done a 60e on my back 5 times, and it kinda blows, but its not impossible. just like any job, itd be easier on a lift but i dont got one. So id ive have stuggle with the stall bolts as well as the top bell housing bolts. But nothing i havent done before.

On the flipside, if im just throwing the motor n suspension on its own, ill be able to do it prob mid next week. Just waiting on my headers to get here. Then i would throw them on the motor, motor to the subframe, throw it on a dolley and get under there. (it would be easiest to install Long tubes while the engine is out right?)

Once the engine is in, id be able to bring the car back inside my garage and finish all the little stuff i have to do. Without having to worry about rain or light... and insects. Id be able to run the battery lines, all the guage and the wiring to go along with it. and then when i have the money for the converter, throw it in on a nice climate controlled smooth floor vs the grooved concrete driveway.


cast your votes.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-08-2017, 07:07 PM   #2
Blackbirdws6
Lord of the rings / 10 Second Club / Meet Coordinator
 
Blackbirdws6's Avatar
 
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,351
iTrader: (3)
Find a thinner FRIEND to do option A with everything assembled outside the car.
__________________

97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140

'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
Blackbirdws6 is offline   Reply With Quote
Old 08-08-2017, 07:56 PM   #3
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,339
iTrader: (12)
I just don't see any time saved shoving the motor in now since its more of a pain to do trans after. Don't you have a sweet crane setup? Between that and a jack, pick car and trans up and tighten cross member bolts up.
__________________
sweetbmxrider is offline   Reply With Quote
Old 08-08-2017, 08:04 PM   #4
LTb1ow
Mongo the Meet Coordinator
 
LTb1ow's Avatar
 
Join Date: May 2008
Posts: 16,892
iTrader: (8)
Do it once right. Least when you can
__________________
Quote:
Originally Posted by KirkEvil View Post
repo bigals turd gen and part it out to a loving home
LTb1ow is offline   Reply With Quote
Old 08-08-2017, 08:16 PM   #5
ThoR294
^^^Lover of bad cars^^^ Meet Coordinator
 
Join Date: Aug 2007
Location: Whitehouse Station
Posts: 2,244
iTrader: (1)
A.

/thread
__________________
1986 Honda VFR750 - 89.3HP to the wheel
2000 Trans Am M6 - Mods: Yes.
2018 Durango R/T - AFE Intake, JLT Catch Can, Stainless Works Catback, Vinyl Dodge Racing Stripes
2003 Toyota Matrix XRS M6 - Lol
ThoR294 is offline   Reply With Quote
Old 08-09-2017, 05:05 AM   #6
Jersey Mike
Power Member/NJFBOA Bookie/Moderator
 
Jersey Mike's Avatar
 
Join Date: Jun 2009
Location: North Jersey = Best Jersey.
Posts: 4,435
iTrader: (12)
Social Networks:

Wait.


Signed,
The guy that's going on year 17
__________________

1995 Firebird... Stock-ish.
Quote:
Originally Posted by LS1ow View Post
Good. He microwaved my phone 6 years ago, i hope his intake erupts.
Jersey Mike is offline   Reply With Quote
Old 08-09-2017, 07:23 AM   #7
PolarBear
Ebearnezer Scrooge/Power Member/Lips
 
PolarBear's Avatar
 
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
iTrader: (16)
How about, don't go on vacation and use that money TOWARDS the converter, then you can get it done early
PolarBear is offline   Reply With Quote
Old 08-09-2017, 07:39 AM   #8
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Quote:
Originally Posted by PolarBear View Post
How about, don't go on vacation and use that money TOWARDS the converter, then you can get it done early
bc the gf may be short, but she packs a lot of grumpy into that short.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"

Last edited by LS1ow; 08-09-2017 at 07:39 AM.
LS1ow is offline   Reply With Quote
Old 08-09-2017, 07:41 AM   #9
PolarBear
Ebearnezer Scrooge/Power Member/Lips
 
PolarBear's Avatar
 
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
iTrader: (16)
Quote:
Originally Posted by LS1ow View Post
bc the gf may be short, but she packs a lot of grumpy into that short.


Just remember, it's better to ask for forgiveness than it is permission

Last edited by PolarBear; 08-09-2017 at 07:42 AM.
PolarBear is offline   Reply With Quote
Old 08-09-2017, 08:33 AM   #10
ThoR294
^^^Lover of bad cars^^^ Meet Coordinator
 
Join Date: Aug 2007
Location: Whitehouse Station
Posts: 2,244
iTrader: (1)
Quote:
Originally Posted by PolarBear View Post


Just remember, it's better to ask for forgiveness than it is permission
This x10000
__________________
1986 Honda VFR750 - 89.3HP to the wheel
2000 Trans Am M6 - Mods: Yes.
2018 Durango R/T - AFE Intake, JLT Catch Can, Stainless Works Catback, Vinyl Dodge Racing Stripes
2003 Toyota Matrix XRS M6 - Lol
ThoR294 is offline   Reply With Quote
Old 08-09-2017, 06:26 PM   #11
IROCZman15
10 Second Club / Meet Coordinator
 
IROCZman15's Avatar
 
Join Date: Dec 2004
Location: Roxbury, NJ
Posts: 2,100
iTrader: (8)
option A. easier
(yet ive never done an engine/trans install in a 4th gen)
__________________
1987 IROC-Z - modified

IROCZman15 is offline   Reply With Quote
Old 08-09-2017, 08:38 PM   #12
MDSheds_SS
11 sec club
 
MDSheds_SS's Avatar
 
Join Date: Aug 2014
Location: Woodbridge
Posts: 834
iTrader: (1)
Social Networks:

I'd say wait and do it all together. Those trans bolt suck even when on a lift. Can't imagine on the ground. Also plugs and headers all in one shot.
__________________
99 Z28 Trick Flow 215s milled to 61cc 228/232 Cam Fast 102 built 4l65e trans 4000 converter 12 bolt 410s Electric WP deleted PS/AC Dyno & Track tuned
2015 ATS Coupe. AWD 2.0 Turbo
2012 2500hd Silverado with LTZ 20s on 35x12.5x20
86 Buick GN Lesabre 1 of 117 (4-Sale)
MDSheds_SS is offline   Reply With Quote
Old 08-09-2017, 09:46 PM   #13
ThoR294
^^^Lover of bad cars^^^ Meet Coordinator
 
Join Date: Aug 2007
Location: Whitehouse Station
Posts: 2,244
iTrader: (1)
Quote:
Originally Posted by MDSheds_SS View Post
I'd say wait and do it all together. Those trans bolt suck even when on a lift. Can't imagine on the ground. Also plugs and headers all in one shot.
I did it on the ground. Lol super long extension and swivel!
__________________
1986 Honda VFR750 - 89.3HP to the wheel
2000 Trans Am M6 - Mods: Yes.
2018 Durango R/T - AFE Intake, JLT Catch Can, Stainless Works Catback, Vinyl Dodge Racing Stripes
2003 Toyota Matrix XRS M6 - Lol
ThoR294 is offline   Reply With Quote
Old 08-15-2017, 07:29 PM   #14
BonzoHansen
Admin.
 
BonzoHansen's Avatar
 
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,149
iTrader: (27)
one word: sawzall
__________________
Vent Windows Forever!

The looser the waistband, the deeper the quicksand. Or so I have read.

Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.

Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
BonzoHansen is offline   Reply With Quote
Old 08-16-2017, 08:08 AM   #15
LTb1ow
Mongo the Meet Coordinator
 
LTb1ow's Avatar
 
Join Date: May 2008
Posts: 16,892
iTrader: (8)
Quote:
Originally Posted by BonzoHansen View Post
one word: sawzall
Not nearly as dangerous and thrilling as a cutoff wheel while working upside down.
__________________
Quote:
Originally Posted by KirkEvil View Post
repo bigals turd gen and part it out to a loving home
LTb1ow is offline   Reply With Quote
Old 08-16-2017, 08:12 AM   #16
BonzoHansen
Admin.
 
BonzoHansen's Avatar
 
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,149
iTrader: (27)
i am very safety conscious
__________________
Vent Windows Forever!

The looser the waistband, the deeper the quicksand. Or so I have read.

Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.

Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
BonzoHansen is offline   Reply With Quote
Old 08-18-2017, 10:15 AM   #17
Featherburner
 
Join Date: Jun 2007
Location: Arm pit of the world... NJ
Posts: 2,673
iTrader: (1)
Quote:
Originally Posted by BonzoHansen View Post
one word: sawzall
Quote:
Originally Posted by LTb1ow View Post
Not nearly as dangerous and thrilling as a cutoff wheel while working upside down.
My personal favorite, the plasma cutter!
__________________
John
Featherburner is offline   Reply With Quote
Reply

  NJFBOA - Home of New Jersey's Camaros and Firebirds > Tech Forums > General Tech

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Sponsor List














All times are GMT -5. The time now is 05:43 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.