Today's Posts Mark Forums Read Calendar
Go Back   NJFBOA - Home of New Jersey's Camaros and Firebirds > Camaros, Firebirds and the People that own them > Member's Projects

Notices


Reply
 
Thread Tools
Old 12-07-2013, 09:57 AM   #26
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
I know the last post was 6 months ago but I picked up an adjustable PHB to replace my non adjustable. It's getting close to being fired. Just need a battery and to adjust the rockers, and new plugs.
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 06-18-2014, 04:28 PM   #27
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
Finally done with school and working full time. Over the last couple weeks I installed half of my LCA's and took off the Axleback(muffler and tips) and installed a spiral flow and dump. My jacks are completely dead and are probably not even worth it to take it apart and fix.

I've come to the conclusion about 1/4 of my budget is going to valve covers to get my stud girdles in to stop breaking studs.
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 06-18-2014, 07:39 PM   #28
WildBillyT
Ayatollah of Rock N Rolla / Admin
 
WildBillyT's Avatar
 
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
iTrader: (10)
Did you ever check your valvetrain geometry?
WildBillyT is offline   Reply With Quote
Old 06-19-2014, 01:07 PM   #29
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
Quote:
Originally Posted by WildBillyT View Post
Did you ever check your valvetrain geometry?
PM sent.
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 06-25-2014, 11:46 AM   #30
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
This car is a nightmare. Now I remember why I stopped working on it for a few years. Yesterday it took me 3 hours to install a LCA on the driverside and I had to unbolt basically everything on the rear to move the lca enough for the holes to line up. Something tells me that relocation brackets and the adjustable PHB will really help this car.

On my quest to make this car somewhat less of a death trap I learned how to adjust drum brakes. It seems pretty straightforward and one side should not be any problem. The other side has a broken spring and I'll be making another thread.

The six o clock spring is busted... http://imgur.com/gBO1QqX
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 06-30-2014, 09:25 PM   #31
B4C
 
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,130
iTrader: (1)
Quote:
Originally Posted by WayFast84 View Post
Yesterday it took me 3 hours to install a LCA on the driverside and I had to unbolt basically everything on the rear to move the lca enough for the holes to line up.
Had the same problem, ratchet strapped the axle to a tree near by and tightened the strap until it lined up.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
B4C is offline   Reply With Quote
Old 11-09-2014, 07:30 AM   #32
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
It's basically been on hold for a while because I had no motivation to do anything after work but lay in the fetal position or get drunk. I'll be fixing the brakes by junking the rear. I already picked up a 12 bolt with 3.73. During black friday I'll be shopping for some aftermarket disc brakes, a driveshaft, loop and LCA's.

I'm still working on the motor, the entire valve train is going to be checked and upgraded when needed.
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 01-14-2017, 04:21 PM   #33
Jersey Mike
Power Member/NJFBOA Bookie/Moderator
 
Jersey Mike's Avatar
 
Join Date: Jun 2009
Location: North Jersey = Best Jersey.
Posts: 4,435
iTrader: (12)
Social Networks:

Any update on this?
__________________

1995 Firebird... Stock-ish.
Quote:
Originally Posted by LS1ow View Post
Good. He microwaved my phone 6 years ago, i hope his intake erupts.
Jersey Mike is offline   Reply With Quote
Old 01-14-2017, 05:29 PM   #34
PolarBear
Ebearnezer Scrooge/Power Member/Lips
 
PolarBear's Avatar
 
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
iTrader: (16)
Quote:
Originally Posted by Jersey Mike View Post
Any update on this?
Way to revive a dead thread
PolarBear is offline   Reply With Quote
Old 01-14-2017, 05:48 PM   #35
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Quote:
Originally Posted by Jersey Mike View Post
Any update on this?
Mike are you drunk posting?
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 01-14-2017, 11:01 PM   #36
Jersey Mike
Power Member/NJFBOA Bookie/Moderator
 
Jersey Mike's Avatar
 
Join Date: Jun 2009
Location: North Jersey = Best Jersey.
Posts: 4,435
iTrader: (12)
Social Networks:

Lmao, he commented in the "Winter Project" thread about pulling a motor... wasn't sure what ever came of this project & was bored enough to find out. Sue me
__________________

1995 Firebird... Stock-ish.
Quote:
Originally Posted by LS1ow View Post
Good. He microwaved my phone 6 years ago, i hope his intake erupts.
Jersey Mike is offline   Reply With Quote
Old 02-26-2017, 06:24 AM   #37
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
Junked the project and decided to go full on LS1 Swap. I have a motor from an 01 Trans am and basically everything else except for the fuel system, tuned computer and a new water pump. I also need brake lines for my 12 bolt with LS1 rear brakes. My goal is to have it done by June 1st.
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 02-26-2017, 09:52 PM   #38
Punkmaster 98
 
Punkmaster 98's Avatar
 
Join Date: Nov 2011
Location: Manalapan,NJ
Posts: 216
iTrader: (0)
Quote:
Originally Posted by WayFast84 View Post
Junked the project and decided to go full on LS1 Swap. I have a motor from an 01 Trans am and basically everything else except for the fuel system, tuned computer and a new water pump. I also need brake lines for my 12 bolt with LS1 rear brakes. My goal is to have it done by June 1st.
Not sure what your plan is but the oem carb fuel line from the 84 will work, you could also swap to TPI/TBI fuel lines. I have the part nbumbers for the correct AN conversion fitting to 6an that goes on the end if you need.
__________________
92 Firebird (First Car SOLD 2/18/17)
90 Firebird Formula 305 T5 Daily Driver (SOLD)
87 GTA Gunmetal RIP
1984 Trans Am 6.0 4L60E , Ford 8.8 3.55 gears
1991 Trans Am
1985 Iroc Z
2015 Silverado 2500HD
Punkmaster 98 is offline   Reply With Quote
Old 02-27-2017, 06:51 AM   #39
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
I'm looking for the easiest long term solution. Part of me thinks a 99+ LS1 tank with a walboro and GTP fuel sending unit. This gives me more anxiety than wiring.

Edit. I just want the fuel level gauge to work and in tank pump basically.
__________________
1984 Firebird
2000 Z28

Last edited by WayFast84; 02-27-2017 at 06:59 AM.
WayFast84 is offline   Reply With Quote
Old 02-27-2017, 08:56 PM   #40
Punkmaster 98
 
Punkmaster 98's Avatar
 
Join Date: Nov 2011
Location: Manalapan,NJ
Posts: 216
iTrader: (0)
Quote:
Originally Posted by WayFast84 View Post
I'm looking for the easiest long term solution. Part of me thinks a 99+ LS1 tank with a walboro and GTP fuel sending unit. This gives me more anxiety than wiring.

Edit. I just want the fuel level gauge to work and in tank pump basically.
factory TPI/tbi sending unit will work also. 99 and up tank works as well as factory tank.
__________________
92 Firebird (First Car SOLD 2/18/17)
90 Firebird Formula 305 T5 Daily Driver (SOLD)
87 GTA Gunmetal RIP
1984 Trans Am 6.0 4L60E , Ford 8.8 3.55 gears
1991 Trans Am
1985 Iroc Z
2015 Silverado 2500HD
Punkmaster 98 is offline   Reply With Quote
Old 03-16-2017, 12:46 PM   #41
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
I got a Wix Vette filter/regulator, TPI sending unit and a Walboro hot kit. Any idea about the fittings I'll need?
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 03-16-2017, 03:25 PM   #42
wretched73
 
wretched73's Avatar
 
Join Date: Nov 2007
Location: Jackson, NJ
Posts: 1,715
iTrader: (2)
How TF is this still going on?? When was the last time the car ran? 2009?
__________________
1983 camaro- Scrap
1988 camaro- Also scrap
'05 Silverado- You guessed it, scrap
1988 TRX 250R- Ported w/ high compression on 110 octane- Out 60' your LT1

Jersey Shore Street Car Takeover (JSSCT) Founder

Quote:
Originally Posted by LS1ow View Post
and once i get PHB, what do i ajust it too?
Quote:
Originally Posted by Jersey Mike View Post
Seven.
wretched73 is offline   Reply With Quote
Old 03-16-2017, 03:46 PM   #43
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
2012. Decided to park it while I finished school. Graduated a few years ago and been saving up parts with what money I have left over after paying bills and maxing out retirement accounts.
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 03-16-2017, 03:48 PM   #44
wretched73
 
wretched73's Avatar
 
Join Date: Nov 2007
Location: Jackson, NJ
Posts: 1,715
iTrader: (2)
Quote:
Originally Posted by WayFast84 View Post
2012. Decided to park it while I finished school. Graduated a few years ago and been saving up parts with what money I have left over after paying bills and maxing out retirement accounts.
Did you get it running with the 400?
__________________
1983 camaro- Scrap
1988 camaro- Also scrap
'05 Silverado- You guessed it, scrap
1988 TRX 250R- Ported w/ high compression on 110 octane- Out 60' your LT1

Jersey Shore Street Car Takeover (JSSCT) Founder

Quote:
Originally Posted by LS1ow View Post
and once i get PHB, what do i ajust it too?
Quote:
Originally Posted by Jersey Mike View Post
Seven.
wretched73 is offline   Reply With Quote
Old 03-16-2017, 10:22 PM   #45
Punkmaster 98
 
Punkmaster 98's Avatar
 
Join Date: Nov 2011
Location: Manalapan,NJ
Posts: 216
iTrader: (0)
Quote:
Originally Posted by WayFast84 View Post
I got a Wix Vette filter/regulator, TPI sending unit and a Walboro hot kit. Any idea about the fittings I'll need?
Its up to you on where you want to mount it. if you want to make use of stock lines you can mount the filter in the bay. you will need the correct AN lines that go onto the factory v8 carb lines. if i recall the ends are not threaded on those in the bay.
__________________
92 Firebird (First Car SOLD 2/18/17)
90 Firebird Formula 305 T5 Daily Driver (SOLD)
87 GTA Gunmetal RIP
1984 Trans Am 6.0 4L60E , Ford 8.8 3.55 gears
1991 Trans Am
1985 Iroc Z
2015 Silverado 2500HD
Punkmaster 98 is offline   Reply With Quote
Old 03-16-2017, 10:26 PM   #46
Punkmaster 98
 
Punkmaster 98's Avatar
 
Join Date: Nov 2011
Location: Manalapan,NJ
Posts: 216
iTrader: (0)
this may be of help

__________________
92 Firebird (First Car SOLD 2/18/17)
90 Firebird Formula 305 T5 Daily Driver (SOLD)
87 GTA Gunmetal RIP
1984 Trans Am 6.0 4L60E , Ford 8.8 3.55 gears
1991 Trans Am
1985 Iroc Z
2015 Silverado 2500HD
Punkmaster 98 is offline   Reply With Quote
Old 04-01-2017, 06:45 AM   #47
WayFast84
 
WayFast84's Avatar
 
Join Date: Nov 2005
Location: Edison
Posts: 7,855
iTrader: (7)
Got the fittings. Bought a grand worth of parts this month and I need to pay off my C.C. before I get the brake lines and cables. Anyone use Flynbye? They have a couple different lines/cables for rear brake swaps.
__________________
1984 Firebird
2000 Z28
WayFast84 is offline   Reply With Quote
Old 04-01-2017, 06:57 AM   #48
Jersey Mike
Power Member/NJFBOA Bookie/Moderator
 
Jersey Mike's Avatar
 
Join Date: Jun 2009
Location: North Jersey = Best Jersey.
Posts: 4,435
iTrader: (12)
Social Networks:

Quote:
Originally Posted by WayFast84 View Post
Anyone use Flynbye? They have a couple different lines/cables for rear brake swaps.
Only once & it was years ago. Communication was atrocious, wait time was torture, but price was fair & product was stellar.
I intend to use them again in the future, if that tells you anything.
__________________

1995 Firebird... Stock-ish.
Quote:
Originally Posted by LS1ow View Post
Good. He microwaved my phone 6 years ago, i hope his intake erupts.
Jersey Mike is offline   Reply With Quote
Old 04-01-2017, 10:49 AM   #49
PolarBear
Ebearnezer Scrooge/Power Member/Lips
 
PolarBear's Avatar
 
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
iTrader: (16)
Quote:
Originally Posted by WayFast84 View Post
Anyone use Flynbye?
I have several times. You'll never actually get in touch with them, but you'll get what you order, eventually.
PolarBear is offline   Reply With Quote
Old 04-01-2017, 11:58 AM   #50
WildBillyT
Ayatollah of Rock N Rolla / Admin
 
WildBillyT's Avatar
 
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
iTrader: (10)
Quote:
Originally Posted by WayFast84 View Post
Got the fittings. Bought a grand worth of parts this month and I need to pay off my C.C. before I get the brake lines and cables. Anyone use Flynbye? They have a couple different lines/cables for rear brake swaps.
Seemed like a guy running a business from his house. I ordered a 93-97 rear axle line and it did not fit. Quality seemed good but I had to re-flare.
WildBillyT is offline   Reply With Quote
Reply

  NJFBOA - Home of New Jersey's Camaros and Firebirds > Camaros, Firebirds and the People that own them > Member's Projects

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Sponsor List














All times are GMT -5. The time now is 03:53 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.