Today's Posts Mark Forums Read Calendar
Go Back   NJFBOA - Home of New Jersey's Camaros and Firebirds > Camaros, Firebirds and the People that own them > Member's Projects

Notices


Reply
 
Thread Tools
Old 08-16-2018, 06:49 AM   #1901
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Quote:
Originally Posted by sweetbmxrider View Post
You had the parking lights on too, right?
Yar.

Quote:
Originally Posted by Jersey Mike View Post
Do you have HID or halogen fogs?
LED bulbs in stock housings.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-16-2018, 07:58 PM   #1902
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,339
iTrader: (12)
Leds should be directional, as they are light emitting diodes and diodes are directional. I would grab a test light and make sure you got pah and gruh.

Brown is power in from headlight switch.

Yellow is power out to fog lamp relay.

Light Green is indicator lamp.

Gray is switch illumination.

Black is ground.


The brown also feeds the power input side of the relay. The purple goes to the lights themselves.
__________________
sweetbmxrider is offline   Reply With Quote
Old 08-17-2018, 08:45 AM   #1903
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

were is this fog light relay you speak of?

And ill check to see if i have them backwards, but even if i did wouldnt the light on the switch light up ?
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"

Last edited by LS1ow; 08-17-2018 at 09:00 AM.
LS1ow is offline   Reply With Quote
Old 08-17-2018, 04:34 PM   #1904
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,339
iTrader: (12)
Yeah switch would light up.

Driver side electrical center #1 which is closer to the strut tower. Its one of the two small relays. The other small one is the horn. The three large ones are for fans.
__________________

Last edited by sweetbmxrider; 08-17-2018 at 04:35 PM.
sweetbmxrider is offline   Reply With Quote
Old 08-17-2018, 07:42 PM   #1905
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Switch was bad. Had extra one upstairs in shop from previous part out, we have illumination
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-17-2018, 08:37 PM   #1906
LTb1ow
Mongo the Meet Coordinator
 
LTb1ow's Avatar
 
Join Date: May 2008
Posts: 16,892
iTrader: (8)
muy bien
__________________
Quote:
Originally Posted by KirkEvil View Post
repo bigals turd gen and part it out to a loving home
LTb1ow is offline   Reply With Quote
Old 08-18-2018, 08:16 AM   #1907
The_Bishop
Power Member
 
The_Bishop's Avatar
 
Join Date: Sep 2008
Location: Hackettstown, NJ
Posts: 1,631
iTrader: (3)
Let there be light?
__________________
1998 Z-28 - SLP lid - Ported TB - LS6 Intake - Dynatech SS headers/Catted Y - Magnaflow Exh - 3.42 - Yank SS3600 - UMI weld-in subframe connectors, Adj LCA, Adj PHB, Q1A TA - Bolt-in Relocation Brackets - Strano springs - Koni shocks - 17" C6Z06 wheels - 326HP/335ft-lbs - 12.35 @ 110.41

Quote:
Originally Posted by Blackbirdws6 View Post
I can appreciate a dream but this person needed some real friends.
The_Bishop is offline   Reply With Quote
Old 08-21-2018, 11:31 AM   #1908
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Was super dissapoint with the LED bulbs in the stock fog housings, and a big bad birdy told me HIDs dont fit well in them... so i compromised. Had a set of 3" round LED fog lights from #JeepLife laying around, and this is the end result.

Before, factory nonsense.



Now, Jeep Life.







They bolted right up to the factory mount using the factory hardware. Just had to bend the tabs out to clear the larger light housing. Im going to end up cutting them off so it looks cleaner. Will wire them up today and see how they are.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"

Last edited by LS1ow; 08-21-2018 at 11:32 AM.
LS1ow is offline   Reply With Quote
Old 08-21-2018, 11:48 AM   #1909
LTb1ow
Mongo the Meet Coordinator
 
LTb1ow's Avatar
 
Join Date: May 2008
Posts: 16,892
iTrader: (8)
Do you have a jeep thing on your air dam as well....?

fuggin heep bros
__________________
Quote:
Originally Posted by KirkEvil View Post
repo bigals turd gen and part it out to a loving home
LTb1ow is offline   Reply With Quote
Old 08-21-2018, 04:06 PM   #1910
ar0ck
Resident Camera Guy
 
ar0ck's Avatar
 
Join Date: Aug 2004
Location: North Jersey
Posts: 10,971
iTrader: (2)
Social Networks:

Got a part number on those? I was thinking of doing something similar on the Trans Am myself!
__________________
ar0ck is offline   Reply With Quote
Old 08-21-2018, 04:48 PM   #1911
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,339
iTrader: (12)
Bls has a factory drop in setup that is led
__________________
sweetbmxrider is offline   Reply With Quote
Old 08-22-2018, 06:33 AM   #1912
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Quote:
Originally Posted by LTb1ow View Post
Do you have a jeep thing on your air dam as well....?

fuggin heep bros
Bruh your like 15 thread pages late on that.

Quote:
Originally Posted by ar0ck View Post
Got a part number on those? I was thinking of doing something similar on the Trans Am myself!
Welp, recycling went out this morn so box is gone. Ill dig threw my amazon history.

Quote:
Originally Posted by sweetbmxrider View Post
Bls has a factory drop in setup that is led
BLS texted me literally 24 hours after i did this offering me them.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-24-2018, 02:43 PM   #1913
Blackbirdws6
Lord of the rings / 10 Second Club / Meet Coordinator
 
Blackbirdws6's Avatar
 
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,351
iTrader: (3)
So lights are cool and all but has this thing made a pass down the 1/4 yet? (Consequences!)
__________________

97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140

'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
Blackbirdws6 is offline   Reply With Quote
Old 08-24-2018, 03:13 PM   #1914
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Quote:
Originally Posted by Blackbirdws6 View Post
So lights are cool and all but has this thing made a pass down the 1/4 yet? (Consequences!)
Sadly i havent even really had the chance to beat on it. I have the front end apart for some other things besides dem LEDs, and i just got the injectors back from being cleaned and matched. Theyre in already, but im dead in the water without a new flash to the PCM for the larger injectors/other changes.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-27-2018, 03:18 PM   #1915
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Finally had a sec to wire the LED fogs up. They are a flood beam so they kinda throw light everywhere. But i think them sitting so back in the bumper will help not destroy oncoming traffics retinas .



__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-27-2018, 03:24 PM   #1916
Blackbirdws6
Lord of the rings / 10 Second Club / Meet Coordinator
 
Blackbirdws6's Avatar
 
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,351
iTrader: (3)
You're now "that guy".
__________________

97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140

'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
Blackbirdws6 is offline   Reply With Quote
Old 08-27-2018, 03:42 PM   #1917
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Part 2 of front end off shens is this.

Ive been planning on changing the intake set up and i wanted to do so before the car hits the dyno. I came across a deal on a Chris1313 Non Ac ram air set up so i scooped that up. And i also came a cross a 104mm lid to go with it as well in place of the cracked SLP lid. Previously the transcooler was mounted at the bottom of the rad, that needed to be moved to fit the larger non AC ram air set up. The lid should be here today or tomorrow.




__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-27-2018, 03:51 PM   #1918
wretched73
 
wretched73's Avatar
 
Join Date: Nov 2007
Location: Jackson, NJ
Posts: 1,715
iTrader: (2)
That intake is neat-o. Do other people have issues with overheating when they run it? it looks like it covers the majority of the radiator.
__________________
1983 camaro- Scrap
1988 camaro- Also scrap
'05 Silverado- You guessed it, scrap
1988 TRX 250R- Ported w/ high compression on 110 octane- Out 60' your LT1

Jersey Shore Street Car Takeover (JSSCT) Founder

Quote:
Originally Posted by LS1ow View Post
and once i get PHB, what do i ajust it too?
Quote:
Originally Posted by Jersey Mike View Post
Seven.
wretched73 is offline   Reply With Quote
Old 08-27-2018, 03:57 PM   #1919
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Quote:
Originally Posted by wretched73 View Post
That intake is neat-o. Do other people have issues with overheating when they run it? it looks like it covers the majority of the radiator.
Its hard to tell in the pics but it doesnt sit right against the rad with exception of the top 2" or so were it goes into the air lid. It covers the front of the rad, but none of the air that comes up from the bottom off the little plastic air duct thing. And i think thats were the rad gets most of its cooling from.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"

Last edited by LS1ow; 08-27-2018 at 03:58 PM.
LS1ow is offline   Reply With Quote
Old 08-27-2018, 04:22 PM   #1920
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,339
iTrader: (12)
Yeah it would be very similar to stock since there is a plastic shroud to help channel air from the air dam across the radiator. If anything, adding more material to block the air from going anywhere else but the radiator would be a good thing.
__________________
sweetbmxrider is offline   Reply With Quote
Old 08-28-2018, 08:49 AM   #1921
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Welp, this rad talk must have jinxed me. Pulled the car out of the garage to work on another project inside. Let the car idle for a few mins just to get some fluid moving... andddd its leaking coolant. The bottom of the ram air is pretty sharp, i must have sliced into the rad a bit when installing. New rad is on the way.
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-28-2018, 10:15 AM   #1922
The_Bishop
Power Member
 
The_Bishop's Avatar
 
Join Date: Sep 2008
Location: Hackettstown, NJ
Posts: 1,631
iTrader: (3)
Quote:
Originally Posted by LS1ow View Post
i just got the injectors back from being cleaned and matched.
Who'd you send the injectors to?
__________________
1998 Z-28 - SLP lid - Ported TB - LS6 Intake - Dynatech SS headers/Catted Y - Magnaflow Exh - 3.42 - Yank SS3600 - UMI weld-in subframe connectors, Adj LCA, Adj PHB, Q1A TA - Bolt-in Relocation Brackets - Strano springs - Koni shocks - 17" C6Z06 wheels - 326HP/335ft-lbs - 12.35 @ 110.41

Quote:
Originally Posted by Blackbirdws6 View Post
I can appreciate a dream but this person needed some real friends.
The_Bishop is offline   Reply With Quote
Old 08-28-2018, 10:15 AM   #1923
Blackbirdws6
Lord of the rings / 10 Second Club / Meet Coordinator
 
Blackbirdws6's Avatar
 
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,351
iTrader: (3)
Pretty rad bro. Clock is ticking!
__________________

97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140

'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
Blackbirdws6 is offline   Reply With Quote
Old 08-28-2018, 12:47 PM   #1924
LS1ow
Power Member / trans break does not equal transbrake
 
LS1ow's Avatar
 
Join Date: May 2009
Location: The Meadowlands
Posts: 4,512
iTrader: (15)
Social Networks:

Quote:
Originally Posted by The_Bishop View Post
Who'd you send the injectors to?
My tuner has the machine at his shop in linden

http://www.speedperf6rmanc3.com/
__________________
99 Z28 - SBE LS1/60e
Motor - 10.84 @ 128 - 1.47 60'
Nitrous - 10.16 @ 132 - 1.40 60"
LS1ow is offline   Reply With Quote
Old 08-28-2018, 08:04 PM   #1925
The_Bishop
Power Member
 
The_Bishop's Avatar
 
Join Date: Sep 2008
Location: Hackettstown, NJ
Posts: 1,631
iTrader: (3)
Nice. May have mine done at some point. What injectors you have in yours?
__________________
1998 Z-28 - SLP lid - Ported TB - LS6 Intake - Dynatech SS headers/Catted Y - Magnaflow Exh - 3.42 - Yank SS3600 - UMI weld-in subframe connectors, Adj LCA, Adj PHB, Q1A TA - Bolt-in Relocation Brackets - Strano springs - Koni shocks - 17" C6Z06 wheels - 326HP/335ft-lbs - 12.35 @ 110.41

Quote:
Originally Posted by Blackbirdws6 View Post
I can appreciate a dream but this person needed some real friends.
The_Bishop is offline   Reply With Quote
Reply

  NJFBOA - Home of New Jersey's Camaros and Firebirds > Camaros, Firebirds and the People that own them > Member's Projects

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Sponsor List














All times are GMT -5. The time now is 03:14 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.