PDA

View Full Version : need a good engine builder

97ws6
08-29-2006, 10:05 PM
Hey guys i am looking to build an LT-1 stroker motor. What shop have you guys used, i am in the Central Jersey area, Ocean County.
NJSPEEDER
08-30-2006, 07:24 PM
to get the bottom end together you really just need a good engine builder. the lower portion of the block fits together the same as a Gen1 SBC.
HardcoreZ28
08-30-2006, 08:10 PM
PM Sent
97ws6
08-31-2006, 02:33 PM
Alright here is what I have decided


Check block, crank and rods for tolerances
Block dipped and cleaned
Magnafluxed to check for cracks
Balance rotating assembly
Bore 30 over to 355,
Align honed for cam and crank
Install new cam bearings, freeze plugs, block plugs
Install stock crank and rods with 30 over pistons
Install new high volume oil pump, radical cam, timing chain, lifters
Install new heads, (probably AFR, maybe Trickflow, or LE), pushrods, roller rockers,
Check piston to valve clearance
Install intake, valve covers, oil pan


This should put me at a complete long ready to install in my car, than I will install it and get a tune.
NJSPEEDER
08-31-2006, 04:00 PM
nice. do you have a whole head+cam+intake combo worked out yet?
camaroracer1992
08-31-2006, 07:52 PM
go to lorenzos in PA he does awesome work
97ws6
08-31-2006, 08:08 PM
NO I DONT HAVE THE HEAD AND CAM COMBO PICKED YET, BUT I AM UP FOR SUGGESTIONS
chrisfrom nj
09-02-2006, 08:09 PM
go with hardcorez28 he did untame daves engine and it runs great
unstable bob gable
09-02-2006, 10:55 PM
I'd suggest some good rod bolts like ARPs be added to your list. :)
BluMaj24
10-05-2006, 05:19 PM
97WS6. Did you ever find someone good, and how much was the work? I'm looking to do a LT1 build in my 87 IROC, but looking more towards boring .60 over and a friend suggested maybe do a 408 setup. I'm just wondering how much that work is looking to cost me.
JSPERFORMANCE
10-07-2006, 01:33 AM
I thought you were going to build a stroker.. And .060" bored 350 is a 361 not a 400 or 408.. My number is 215-783-4645 if you would like me to build your engine..

Josh
J.S. Performance
Ian
10-07-2006, 05:59 AM
FWIW, both Josh from JS Performance and Paul from RPM Resto and Custom are both great guys.
JSPERFORMANCE
10-08-2006, 09:40 AM
Thank you very much, Ian
njfastestcamaro
10-10-2006, 10:45 AM
bill cirelly in peterson great work used them to do alot of work and came out great and he will work out everything with u when u drop it off
NJLT1SS
10-19-2006, 08:15 AM
My motor was done at Bill Ceralli's, they do great machine work. My friend John works there at night, he built my motor. He is there after 6pm or so.
Untamed
10-20-2006, 02:01 PM
go with hardcorez28 he did untame daves engine and it runs great

+1 What he said.
IROCdan330
10-27-2006, 01:42 PM
Josh won't steer you wrong...very easy to get along with, helpful, and does high quality work.
88BluBird
10-27-2006, 07:13 PM
I Agree..Josh is one stand up dude..and has become..dare i say a good friend..he is the ONLY one i trust to work on the rust bird. ive seen him do numerous projects..he will be building my 355..if he know whats good for`em lol
JSPERFORMANCE
10-28-2006, 09:07 AM
thanks dan and tim!! And its not rusted its seasoned!! Just think who is gonna suspect a stock rusted firebird with a ultra quiet exhaust to blow their doors off? ultimate sleeper!!!!!!!! But dan still has you by a bit with the IROC (even with the wrong converter) :lol: see you guys later!
IROCdan330
10-28-2006, 05:29 PM
thanks dan and tim!! And its not rusted its seasoned!! Just think who is gonna suspect a stock rusted firebird with a ultra quiet exhaust to blow their doors off? ultimate sleeper!!!!!!!! But dan still has you by a bit with the IROC (even with the wrong converter) :lol: see you guys later!

hardy f-ing har har