SOTP dyno=likes gains from ported TB

[NJ346]

I just got a ported,polished and epoxed TB on the car and must say I think it really helped the car out. The car has a tune, but for what's done to it I think it was a little conservative. I never did find out what the A/F ratio was at WOT but I'm thinking it was a little on the rich side and hurting me. I think the TB helped lean out the car a little bit and I think I may have seen more than the typical 5 rwhp gain from the ported TB. I will be taking the car to the track when it opens back up to see if my MPH picks up at all.

[JL8Jeff]

The ported TB on the LS1 cars makes a definite SOTP difference. It might be bigger on the A4 cars with no little lag or hesitation. Mine is not epoxied but it was still an obvious difference. Not sure about the actual hp difference, but the change in the way the car drives makes it worth it.

[noboundreez2345]

If you don't mind me asking where did you get the porting and polishing done, or did you do it yourself? Its a mod that I've been thinking about for awhile. My plan modwise for the winter is LS6 intake, p+p throttle body, and pulleys. I figure the combo of these three shud boost the SOPT dyno. Hey op what suspension mods do you have done? Beeing thinking of a shock tower brace and sub frame connectors. Any recommendations?

[NJ Torque]

Its a proven 11 HP on my car.

[MonmouthCtyAntz]

Interesting, so is there an actual gain from a aftermarket tb? Where can u get your throttle body ported at? JS?

[NJ346]

If you don't mind me asking where did you get the porting and polishing done, or did you do it yourself? Its a mod that I've been thinking about for awhile. My plan modwise for the winter is LS6 intake, p+p throttle body, and pulleys. I figure the combo of these three shud boost the SOPT dyno. Hey op what suspension mods do you have done? Beeing thinking of a shock tower brace and sub frame connectors. Any recommendations?

I picked it up of off LS1tech from a wrecked car in toms river. It was from an 00 car so we had to switch the shaft from my old TB to the ported one so that my throttle cable would let the butterfly close(this wasn't fun when all of a sudden the snow decided to start coming down really heavy and we were working on my car outside). For suspension, the strut tower brace is one of the only things my car doesn't have. I always thought that that was more for a car that was concerned about cornering really well(say a roadcoarse car?),but after thinking about it, it may help with even weight distribution towards the back of the car when you launch at the track(again idk). For suspension, definitely do subframe connectors, they made my car feel like a brick sh*thouse, also LCA's and relocation brackets are good too. Try and buy the package deals so you get better prices. I got my panhard bar and LCA's for like $160 shipped to my door. I will throw my car on the dyno later this year to see what I can get when the car is full bolt-ons.

[creeper]

i ported mine myself and it was probably the biggest sotp gain out of what i have done thus far

[NJ Torque]

If you don't mind me asking where did you get the porting and polishing done, or did you do it yourself? Its a mod that I've been thinking about for awhile. My plan modwise for the winter is LS6 intake, p+p throttle body, and pulleys. I figure the combo of these three shud boost the SOPT dyno. Hey op what suspension mods do you have done? Beeing thinking of a shock tower brace and sub frame connectors. Any recommendations?

A LS6/PTB does feel really good... and was definitly a SOTP gain.

SFC do help, as well and I can feel the difference with the STB as well, I also have LCA's. PHB and Torque arm too.

My car made 342/347 which its a crappy 98 and bolt ons only, no underdrive.

-Chris

[JL8Jeff]

Interesting, so is there an actual gain from a aftermarket tb? Where can u get your throttle body ported at? JS?

Not aftermarket, stock TB ported. Search around LS1tech or Ebay, they run around $60 plus the core.

[creeper]

i just sold one for $75 last week. too bad this thread didn't come up sooner hahah.

[MonmouthCtyAntz]

Not aftermarket, stock TB ported. Search around LS1tech or Ebay, they run around $60 plus the core.

Yea just found one 60 plus shipping thx.

[noboundreez2345]

I'm going to keep checking the for sale sections if I don't have any luck I guess i'll attempt to do it myself. I saw a write up on LS1 tech hopefully I wont **** anything up. Thanks for the info guys

[NJ Torque]

Check this one... I have an intake + TB for sale

[creeper]

i bought a ported tb used to put on my car while i ported my own/in case i effed anything up and then when i was done i sold it for $15 more than what i payed.

that's not a free mod, that's a profit mod.

[maroman88]

i bought a ported tb used to put on my car while i ported my own/in case i effed anything up and then when i was done i sold it for $15 more than what i payed.

that's not a free mod, that's a profit mod.

LOL niiiice

[MonmouthCtyAntz]

yea I think im going to get that ported TB and switch my intake to the lid style.

[JL8Jeff]

yea I think im going to get that ported TB and switch my intake to the lid style.

You will most likely need to drill some holes to be able to mount the lid base. I don't know that there is any real advantage to that over the CAI you already have.

[NJ Torque]

You will most likely need to drill some holes to be able to mount the lid base. I don't know that there is any real advantage to that over the CAI you already have.

Unless its a Volant style with the box surrounding it, many say that its a HAI.

[MonmouthCtyAntz]

You will most likely need to drill some holes to be able to mount the lid base. I don't know that there is any real advantage to that over the CAI you already have.

Yea I talked to a few guys on tech and they seemed to think that would be a good gain along w/ the FRA mod...I honestly dont think its worth it.

[rscamaro73]

I tend to watch this guy's PTB auctions....http://motors.shop.ebay.com/merchant/photz6


:mrgreen:

[JL8Jeff]

I tend to watch this guy's PTB auctions....http://motors.shop.ebay.com/merchant/photz6


:mrgreen:

Yeah, he's always porting something! :lol:

[NJ Torque]

Wow.... must be cold down there in Jacksonville.