 |
03-19-2009, 09:35 PM
|
#1
|
|
11 Second Club
Join Date: Feb 2008
Location: Edison, NJ
Posts: 4,620
|
Wheel studs in a 4th gen
How hard is it to do wheel studs on a stock rear?
Where can I get longer then stock units?
__________________
1999 Z28 Convertible. 6 speed swap, wide cowl hood, full hockey stripes, and a whining 10 bolt.
2008 Sierra Vortec Max. 6.2 swapped, headers, Magnaflow catback, GMPP CAI, NHT optioned tow package.
2006 GTO, 11.48 @ 118.3
|
|
|
|
03-20-2009, 12:13 AM
|
#2
|
|
BadMod
Join Date: Aug 2004
Location: hamilton, nj
Posts: 8,889
|
easy after you pull the axle out.....i got arp ones from either speed inc or thunder
__________________
So much stupid, so little time.
Quote:
Originally Posted by 79CamaroDiva
It started before I drove your car. I just have to look at it the wrong way and your car poops parts.
|
Mercerville MotorSports, LLC
|
|
|
|
|
03-20-2009, 10:35 AM
|
#3
|
|
11 Second Club
Join Date: Feb 2008
Location: Edison, NJ
Posts: 4,620
|
mike, must you pull the axles out?
__________________
1999 Z28 Convertible. 6 speed swap, wide cowl hood, full hockey stripes, and a whining 10 bolt.
2008 Sierra Vortec Max. 6.2 swapped, headers, Magnaflow catback, GMPP CAI, NHT optioned tow package.
2006 GTO, 11.48 @ 118.3
|
|
|
|
|
03-20-2009, 01:40 PM
|
#4
|
|
BadMod
Join Date: Aug 2004
Location: hamilton, nj
Posts: 8,889
|
i think the backing plates would get in the way.....im not 100% sure
__________________
So much stupid, so little time.
Quote:
Originally Posted by 79CamaroDiva
It started before I drove your car. I just have to look at it the wrong way and your car poops parts.
|
Mercerville MotorSports, LLC
|
|
|
|
|
03-20-2009, 01:42 PM
|
#5
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,366
|
especially if you are going with longer wheel studs, makes it that much harder.
|
|
|
|
|
03-20-2009, 01:45 PM
|
#6
|
|
BadMod
Join Date: Aug 2004
Location: hamilton, nj
Posts: 8,889
|
yeah... you may be able to hammer the stock ones out, but might get stuck putting the new ones in
__________________
So much stupid, so little time.
Quote:
Originally Posted by 79CamaroDiva
It started before I drove your car. I just have to look at it the wrong way and your car poops parts.
|
Mercerville MotorSports, LLC
|
|
|
|
|
03-20-2009, 02:59 PM
|
#7
|
Join Date: Nov 2008
Posts: 112
|
Yep, the axles absolutely should come out to remove and replace the studs. It's NOT advisable to hammer out the old studs or to use an impact gun and washers to seat the new studs. Both of those methods can damage either the stud's integrity or the axle.
Press the studs. You can use a bench vise. For removal, place a nut on the old stud and a large socket behind the back of the stud. Tighten the vise and the stud will press out of the axle and into the void in the socket. To install the new studs, place the stud into the axle. Place a large socket or piece of pipe over the stud's threads and tighten the vise. This will press the syud in. Stop when the flange of the stud is flush with the back of the axle. We use this method at the track all the time. takes a bit of time and energy, but it works.
__________________
|
|
|
|
|
03-20-2009, 03:04 PM
|
#8
|
|
BadMod
Join Date: Aug 2004
Location: hamilton, nj
Posts: 8,889
|
Quote:
Originally Posted by Jensend
Yep, the axles absolutely should come out to remove and replace the studs. It's NOT advisable to hammer out the old studs or to use an impact gun and washers to seat the new studs. Both of those methods can damage either the stud's integrity or the axle.
Press the studs. You can use a bench vise. For removal, place a nut on the old stud and a large socket behind the back of the stud. Tighten the vise and the stud will press out of the axle and into the void in the socket. To install the new studs, place the stud into the axle. Place a large socket or piece of pipe over the stud's threads and tighten the vise. This will press the syud in. Stop when the flange of the stud is flush with the back of the axle. We use this method at the track all the time. takes a bit of time and energy, but it works.
|
good advice
__________________
So much stupid, so little time.
Quote:
Originally Posted by 79CamaroDiva
It started before I drove your car. I just have to look at it the wrong way and your car poops parts.
|
Mercerville MotorSports, LLC
|
|
|
|
|
03-20-2009, 06:47 PM
|
#9
|
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,165
|
Quote:
Originally Posted by Jensend
Yep, the axles absolutely should come out to remove and replace the studs. It's NOT advisable to hammer out the old studs or to use an impact gun and washers to seat the new studs. Both of those methods can damage either the stud's integrity or the axle.
Press the studs. You can use a bench vise. For removal, place a nut on the old stud and a large socket behind the back of the stud. Tighten the vise and the stud will press out of the axle and into the void in the socket. To install the new studs, place the stud into the axle. Place a large socket or piece of pipe over the stud's threads and tighten the vise. This will press the stud in. Stop when the flange of the stud is flush with the back of the axle. We use this method at the track all the time. takes a bit of time and energy, but it works.
|
Who let the smart guy in?
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
