|
Stuff has gotta go!
Lots and lots of stuff, and I need to get rid of it. Im going to do an engine swap, and I need to get rid of this stuff.
1 whole TPI set up. comes complete with intake, runners, plenum, throttle body, fuel rails with Holley adjustable fuel pressure regulator, 19lb injectors, $300 Plenum and runners are polished, but not to a mirror shine.
Complete, unspliced wire harness from an 87 TPI car, with computer. Tuned and PROM by JS Performance. Chip was tuned for the 305 TPI car with ZZ4 cam, headers, and additional fuel. I belive I have my stock PROM and will offer it with the car if wanted. For whole harness and computer, $150. Harness by itself is $80, computer by itself is $90.
Two sets of TPI runners, non polished: $20 bucks a set
1 set of fuel rails off a L98 car with 22lbs injectors: $30
1 Plenum, non polished, non ported: $15 bucks
1 Throttle body for TPI cars 85-88 cars $35 bucks
1 set of moddified LB9 heads, with new stainless valves, springs, seals, everything. 3,000 miles on the heads, very clean and ran well. Intake valve is larger then the stock 1.85 to a 1.95 inch. $250 bucks with polished aftermarket valve covers. Will come with stock stamped rockers
A ZZ4 cam, with 3000miles on it. With factory roller lifters and pushrods, $75 bucks
Heddman shortie headers, non-air design, ceramic coated by ASC with Y pipe, looking to get $220
700r4 Trans with converter. Under normal driving, shifts fine without problem. Last two times down the track, trans would not shift into third gear. Has near 100k miles on it, does have a leak from the front pump seal, will throw in seal and Corvette servo kit that I never had a chance to install. $200 bucks with stock converter.
SBC water pump, worked great, $5
One MAF for TPI cars, in good working condition, SOLD
1 set of 16x 1.6 Pro Magnum roller rockers from Comp Cams, non-self aligning. Good for SBC's 55-86. Never been used as I needed self-aligning units: SOLD
Power steering pump for 87 Camaro: $15
Alternator, AC Delco 105 amp: $90
AC compressor, not sure of style but came off teh 87 Camaro TPI car: $90
Underdrive pulleys for Vbelt set up, 2 pulley system for alternator and crank: $40
9 Bolt rear with PBR disk brake set up. New rotors, Hawk HPS pads, and stainless lines running to each caliper. 3.27's inside. Axle shaft bearings hum a little, will include a new set of bearings for both left and right side. $150 with brakes.
Set of 4 15x7 Z28 wheels, found on a lot of third gens, with good BFGoodrich Comp TA H rated tires 215/60-15's black wall tires. Need to get rid of them: $100
Free crap:
180* thermostat for SBC's
1 set of center bolt valve covers, stock
1 stock fuel pressure regulator for TPI cars
Stock LB9 "peanut" roller cam.
AIR pump for an 87 Camaro TPI car
EGR valve for TPI engine
Set of 14x6 wheels that came off my 72 Camaro. Need them gone.
195* thermostat for SBC's
PM me with questions. Prices are as always neg.
__________________
2/20/2013: They Day the ****s Stopped
Last edited by BigAls87Z28; 06-29-2010 at 11:48 PM.
|
